The Maxwell distribution of molecular speed of a gaseous system is
dN_c = 4πN(M/2πRT)^(3/2) c² e^(−Mc²/2RT) dc
(Symbols have their usual meanings)
Plot ((1/N) × dN_c/dc) against c—
(i) at two different temperatures T₁ and T₂; T₂ > T₁;
(ii) at two molar masses M₁ and M₂; M₂ > M₁.
Justify your plots.
15 marks · directive: Plot and justify
The core of a good answer
f(c) = (1/N)dN_c/dc rises as c² at low speed, peaks at the most probable speed c_mp = √(2RT/M) and falls exponentially; the area under every curve is 1, so raising T or lowering M moves the peak to higher c and makes the curve lower and broader, while lowering T or raising M gives a taller, narrower peak at lower c.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
Two sketches (8 + 7 marks) with justification from the formula: the shape (c² growth against exponential decay), the position of the maximum by differentiation, the height of the maximum, and normalisation (constant area). Mark c_mp, c_av and c_rms on the curve.
Answer outline
Introduction
f(c) = 4π(M/2πRT)^(3/2) c² exp(−Mc²/2RT) is the fraction of molecules per unit speed interval; ∫₀^∞ f(c) dc = 1.
Step 1: Shape of the curve
- At c = 0, f = 0; for small c the c² term dominates and f rises parabolically.
- At large c the factor exp(−Mc²/2RT) dominates and f falls to zero asymptotically.
- The curve is unsymmetrical, with a long tail on the high speed side.
Step 2: Position and height of the maximum
- df/dc = 0 gives 2c − (M/RT)c³ = 0, so c_mp = √(2RT/M)
- f(c_mp) = (4/√π)(M/2RT)^(1/2) e⁻¹, i.e. peak height ∝ √(M/T)
- Characteristic speeds: c_mp : c_av : c_rms = √2 : √(8/π) : √3 = 1 : 1.128 : 1.225
Step 3: (i) Plot at T₁ and T₂ (T₂ > T₁)
- Both curves start at the origin; the T₂ curve has its maximum at a higher speed (c_mp ∝ √T) and the maximum is lower (height ∝ 1/√T).
- The T₂ curve is broader with a longer high speed tail, and the two curves cross once; the areas under both are equal to 1.
- Example (N₂, M = 0.028 kg mol⁻¹): at 300 K c_mp = 422 m s⁻¹, peak 1.97 × 10⁻³ s m⁻¹; at 600 K c_mp = 597 m s⁻¹, peak 1.39 × 10⁻³ s m⁻¹.
Step 4: (ii) Plot at M₁ and M₂ (M₂ > M₁), same T
- Since T and M appear only as the ratio M/T, increasing M has the same effect as decreasing T.
- The heavier gas M₂ has its peak at lower speed (c_mp ∝ 1/√M), a taller peak (height ∝ √M) and a narrower spread; the lighter gas M₁ gives a lower, broader curve shifted to higher speeds.
- Example at 300 K: He (0.004 kg mol⁻¹) c_mp = 1117 m s⁻¹, peak 7.4 × 10⁻⁴ s m⁻¹; N₂ c_mp = 422 m s⁻¹, peak 1.97 × 10⁻³ s m⁻¹.
Step 5: Physical justification
- Higher temperature means higher mean kinetic energy (3/2 RT per mole), so more molecules move fast and the distribution spreads out.
- Normalisation forces the peak to drop when the curve broadens.
- At a given T all gases have the same mean kinetic energy, so lighter molecules must move faster.
Conclusion
Sketch: two skewed bell shaped curves from the origin; the curve for higher T (or lower M) is flatter, broader and peaks to the right; the curve for lower T (or higher M) is taller, narrower and peaks to the left; equal areas. The fraction of molecules with energy above a threshold rises sharply with T, explaining temperature effects on reaction rates.
Examples and data to cite
- Graham's law of effusion (rate ∝ 1/√M) follows from the dependence of mean speed on molar mass and was used to enrich uranium as UF₆.
Facts to remember
- c_mp = √(2RT/M), c_av = √(8RT/πM), c_rms = √(3RT/M)
- Peak height f(c_mp) = (4/√π)(M/2RT)^(1/2)/e
- ∫₀^∞ f(c) dc = 1
- Distribution depends only on M/T