Why is Teflon chemically inert, while PVC is reactive at high temperatures ? Explain.
5 marks · directive: Explain
The core of a good answer
Teflon (PTFE, −(CF₂−CF₂)ₙ−) is inert because its backbone is wrapped in C−F bonds, the strongest single bonds carbon forms (CH₃−F about 115 kcal mol⁻¹, against 83.7 kcal mol⁻¹ for CH₃−Cl), and it has no C−H bonds; PVC (−(CH₂−CHCl)ₙ−) has weaker C−Cl bonds with hydrogens on the neighbouring carbons, so on heating it loses HCl and is more thermally labile than other commodity polymers.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
The answer must compare bond strengths, structure and the specific degradation pathway of PVC (dehydrochlorination) with the shielding in PTFE.
Answer outline
Introduction
Chemical inertness of a polymer depends on bond energies, polarity and steric protection of the backbone. Both are halogenated addition polymers, but fluorine and chlorine behave very differently.
Why PTFE is inert
- Bond dissociation energies of CH₃−X: F 115, H 104.9, Cl 83.7 kcal mol⁻¹ (about 481, 439 and 350 kJ mol⁻¹); C−F is the strongest single bond to carbon.
- The C−F bond is strongly polar (electronegativity F 4.0, C 2.5); the attractive partial charges add ionic character, and adding more fluorines to the same carbon strengthens and shortens the other C−F bonds, as in CF₂ groups.
- Every carbon of PTFE carries two fluorines and there are no C−H bonds, so there is no easy route for elimination or attack.
- PTFE is hydrophobic with one of the lowest coefficients of friction of any solid; it melts at about 327 °C and begins to deteriorate at about 260 °C.
- Its C−F bonds are attacked only by highly reactive metals such as the alkali metals and by fluorinating agents such as xenon difluoride.
Why PVC is reactive on heating
- C−Cl is much weaker than C−F, and each CHCl carbon has hydrogens on the neighbouring CH₂ carbons, so HCl can be eliminated: −CH₂−CHCl− → −CH=CH− + HCl.
- PVC is more thermally labile than other commodity polymers: degradation begins near 250 °C, while polyethylene holds up to about 400 °C.
- In service, traditional PVC products are limited to around 60 °C, where heat distortion begins.
Practical consequences
- PVC therefore needs heat stabilisers that minimise loss of HCl: traditionally derivatives of heavy metals (lead, cadmium), now increasingly calcium-based stabilisers.
- PTFE is used as a non-stick coating for cookware, as a chemical-resistant gasket material and as a liner for hoses and industrial pipelines.
Conclusion
Strong, polar C−F bonds on every carbon and the absence of C−H bonds make PTFE inert, while weaker C−Cl bonds next to C−H bonds let PVC lose HCl on heating.
Examples and data to cite
- PTFE was discovered accidentally in 1938 by Roy J. Plunkett at DuPont.
- Lead-based heat stabilisers were long used in PVC; calcium-based stabilisers are replacing them.
Facts to remember
- BDE of CH₃−F 115 kcal mol⁻¹; CH₃−Cl 83.7 kcal mol⁻¹.
- PTFE melting point about 327 °C; deteriorates from about 260 °C.
- PVC dehydrochlorination: −CH₂−CHCl− → −CH=CH− + HCl.
- PVC degradation begins near 250 °C; heat stabilisers minimise loss of HCl.