A frictionless pulley A as shown in the figure is supported by two bars AB and AC which are hinged at B and C to a vertical wall. A flexible cable, hinged at D, goes over the pulley and supports a load 30 kN at the other end E. The angles between the members are shown in the figure. Neglecting the size of the pulley, determine the forces in the bars AB and AC by drawing the free body diagram :
[Figure, described in words: B, D and C lie on the vertical wall in that order from top to bottom, with A to the right of the wall. Bar AB makes 60° with the wall at B; the cable portion DA makes 60° with the wall at D; bar AC makes 30° with the wall at C; the angle at A between DA and AC is 30°. The cable leaves the pulley at A vertically downwards to the 30 kN load at E.]
10 marks · directive: Determine
The core of a good answer
Force in AB = 0 and force in AC = 30√3 ≈ 51.96 kN (compression): the resultant of the two equal cable tensions acts exactly along CA, so bar AB carries no force.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
A two-force equilibrium problem at a concurrent point. Because the pulley is frictionless and its size is neglected, the cable tension is the same (30 kN) on both sides of A, and the pin at A is in equilibrium under four concurrent forces: two cable pulls and two bar forces. The free body diagram and two equations of equilibrium (ΣFx = 0, ΣFy = 0), or Lami's theorem after combining the cable forces, give the answer.
Answer outline
Introduction
Take the pin A as free body. Cable tension T = 30 kN in both segments (A to D and A to E). Bars AB and AC are two-force members (hinged at both ends), so their forces act along their axes. Assume tension positive (force on A directed from A towards the far end).
Step 1: Directions of the forces at A
- Wall is vertical. AB makes 60° with the wall, so from A the bar AB points up and to the left at 30° above the horizontal: unit vector (−cos30°, +sin30°).
- DA makes 60° with the wall, so from A the cable to D points down and to the left at 30° below the horizontal: (−cos30°, −sin30°).
- AC makes 30° with the wall, so from A the bar AC points down and to the left at 60° below the horizontal: (−cos60°, −sin60°). Check: angle DAC = 60° − 30° = 30°, as given.
- Cable AE is vertical: (0, −1).
Step 2: Resultant of the cable forces
- R = T(−cos30°, −sin30°) + T(0, −1) = 30(−0.866, −0.5) + 30(0, −1)
- R = (−25.98, −45.00) kN; |R| = √(25.98² + 45²) = 51.96 kN
- Direction: tan⁻¹(45/25.98) = 60° below the horizontal, i.e. exactly along AC (it bisects the 60° angle between AD and AE).
Step 3: Equilibrium of pin A
- ΣFx = 0: −F_AB cos30° − F_AC cos60° − 25.98 = 0
- ΣFy = 0: F_AB sin30° − F_AC sin60° − 45.00 = 0
- Solving: F_AB = 0, F_AC = −51.96 kN
Step 4: Interpretation
- F_AC negative means the bar pushes on A: AC is in compression, 51.96 kN = 30√3 kN.
- AB is a zero-force member for this geometry, because R has no component perpendicular to AC.
- Check with Lami's theorem: three forces R, F_AB, F_AC in equilibrium with R collinear with AC forces F_AB = 0.
Conclusion
F_AB = 0 and F_AC = 51.96 kN (compressive). The free body diagram shows T = 30 kN along AD and AE, the bar AC thrust towards A, and no force in AB.
Examples and data to cite
- A 2T cos(θ/2) rule: two equal tensions T with included angle θ = 60° give a resultant 2 × 30 × cos30° = 51.96 kN along the bisector.
Facts to remember
- A member pinned at both ends and loaded only at its ends is a two-force member, carrying pure tension or pure compression along its axis.
- A string passing over massless, frictionless pulleys keeps the same tension along its length.
- Equilibrium of concurrent forces in a plane: ΣFx = 0 and ΣFy = 0 (two equations, so at most two unknown magnitudes).
- Lami's theorem: for three coplanar, concurrent, non-collinear forces in equilibrium, each force divided by the sine of the angle opposite it (the angle between the other two) is the same.