Draw the bending moment diagram and shear force diagram for the beam ABCD. The beam supports a point load of 12 kN as shown in the figure :
[Figure, described in words: A is a fixed support on the left. AB is horizontal, 2 m long. From B the member turns vertically downwards for 0.6 m to C. From C a horizontal arm CD, 0.3 m long, projects to the right. A vertical downward point load of 12 kN acts at D.]
10 marks · directive: Draw
The core of a good answer
Shear force is 12 kN in AB and CD and zero in BC; bending moment is hogging, 0 at D, 3.6 kN·m at C, constant 3.6 kN·m along BC, and rising linearly to 27.6 kN·m at the fixed end A, which also carries a 12 kN upward reaction.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
A statically determinate cranked cantilever. The task is to find the fixed end reactions, then walk from the free end D towards A, computing shear (perpendicular to each member axis) and bending moment, and sketch both diagrams member by member. The vertical leg BC is the twist: it carries axial force but no shear, and a constant moment.
Answer outline
Introduction
Fixed at A, free at D. Horizontal distance of the load from A = 2 + 0.3 = 2.3 m. Hogging moment taken as negative in sign but plotted on the tension (top) side; values given as magnitudes.
Step 1: Reactions at A
- ΣV = 0: V_A = 12 kN (upward)
- ΣM_A = 0: M_A = 12 × 2.3 = 27.6 kN·m (anticlockwise, hogging)
- No horizontal load, so H_A = 0.
Step 2: Member CD (x measured from D, 0 ≤ x ≤ 0.3 m)
- Shear F = 12 kN (constant)
- M = −12x; M_D = 0, M_C = −12 × 0.3 = −3.6 kN·m
- BMD linear, SFD rectangular.
Step 3: Member BC (vertical, 0.6 m)
- The 12 kN load is parallel to BC, so shear perpendicular to BC = 0; BC carries 12 kN axial tension (C is pulled down by the load through CD).
- The lever arm of the load about any section of BC is constant = 0.3 m, so M = −3.6 kN·m throughout BC (constant).
- Moment is continuous at the rigid joints B and C.
Step 4: Member AB (x measured from B, 0 ≤ x ≤ 2 m)
- Shear F = 12 kN (constant)
- M = −12(0.3 + x); M_B = −3.6 kN·m, M_A = −12 × 2.3 = −27.6 kN·m
- BMD linear from 3.6 to 27.6 kN·m (hogging).
Step 5: Sketch
- SFD: 12 kN rectangle over AB, zero over BC, 12 kN rectangle over CD.
- BMD (tension side): triangle on CD (0 to 3.6), rectangle on BC (3.6), trapezium on AB (3.6 to 27.6).
Conclusion
Maximum shear 12 kN (AB, CD); maximum bending moment 27.6 kN·m hogging at A. Check: M_A equals load × horizontal lever arm 2.3 m, independent of the 0.6 m drop.
Examples and data to cite
- Same procedure as a simple cantilever with point load W at distance a: M_max = Wa at the fixed end.
Facts to remember
- Shear force at a section is the algebraic sum of forces perpendicular to the member axis on one side of the section.
- The slope of the bending moment diagram equals the shear; where shear is zero over a length, the bending moment is constant over that length.
- At a rigid joint with no external moment, moment equilibrium of the joint makes the bending moment continuous from one member to the next.
- A cantilever's fixed end carries the maximum moment, equal to the moment of all loads about the support.