Using limit state method, design a reinforced concrete circular column (with lateral ties) of height 3·0 m. It is subjected to an unfactored axial load of 1150 kN (dead load + live load). Use M25 grade of concrete and Fe500 grade of steel. Take effective length factor as 1·2. Show the design details in a neat sketch.
15 marks · directive: Design
The core of a good answer
A 400 mm diameter tied circular column with 6 bars of 18 mm (1527 mm², 1.21%) and 8 mm ties at 280 mm centres carries P_u = 1725 kN (capacity about 1753 kN); it is a short column (l_e/D = 9) and the minimum eccentricity is within the 0.05D limit.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
A short axially loaded column design under IS 456:2000. Find the factored load, size the section and steel from P_u = 0.4f_ck A_c + 0.67f_y A_sc, check slenderness and minimum eccentricity, then detail longitudinal bars and lateral ties per clause 26.5.3. The sketch shows the cross-section and elevation.
Answer outline
Introduction
P = 1150 kN, P_u = 1.5 × 1150 = 1725 kN; l = 3.0 m, l_e = 1.2 × 3.0 = 3.6 m; f_ck = 25 MPa, f_y = 500 MPa. Clear cover 40 mm.
Step 1: Trial size
- Assume about 1% steel: 1725×10³ = 0.4 × 25 × 0.99A_g + 0.67 × 500 × 0.01A_g = 13.25A_g
- A_g = 130,189 mm², D = 407 mm; try D = 400 mm (A_g = 125,664 mm²) with steel slightly above 1%
Step 2: Slenderness and minimum eccentricity
- l_e/D = 3600/400 = 9 < 12, short column
- l/500 + D/30 = 6 + 13.3 = 19.3 mm, less than the 20 mm minimum, so e_min = 20 mm; 0.05D = 20 mm, so e_min does not exceed 0.05D and the clause 39.3 formula applies
Step 3: Longitudinal steel
- 1725×10³ = 0.4 × 25 × (125664 − A_sc) + 0.67 × 500 × A_sc
- A_sc = (1725000 − 1256637)/325 = 1441 mm² (1.15%)
- Minimum 0.8% = 1005 mm²; provide 6 bars of 18 mm = 1527 mm² (1.21%), at least 6 bars for a circular column
Step 4: Capacity check
- P_u,cap = 0.4 × 25 × (125664 − 1527) + 0.67 × 500 × 1527 = 1241.4 + 511.5 = 1752.9 kN > 1725 kN, safe
Step 5: Lateral ties
- Diameter ≥ max(18/4, 6) = 6 mm; adopt 8 mm circular ties
- Pitch ≤ least of D = 400 mm, 16 × 18 = 288 mm, 300 mm; adopt 280 mm c/c
Step 6: Sketch details
- Cross-section: 400 mm circle, 6 bars of 18 mm equally spaced on a circle, 40 mm clear cover, 8 mm ties.
- Elevation: 3.0 m height, ties at 280 mm c/c throughout.
Conclusion
Provide a 400 mm diameter column, 6 nos. 18 mm Fe500 bars and 8 mm ties at 280 mm c/c; utilisation 1725/1753 ≈ 0.98.
Examples and data to cite
- IS 456 cl. 26.4.2.1: nominal cover to longitudinal bars in a column not less than 40 mm nor less than the bar diameter; 40 mm is used here.
- Using D = 450 mm would allow minimum steel (0.8%) and is an equally valid design choice.
Facts to remember
- IS 456:2000 cl. 39.3: P_u = 0.4 f_ck A_c + 0.67 f_y A_sc, valid when e_min ≤ 0.05D.
- IS 456 cl. 25.1.2: a column is short when l_e/D < 12.
- IS 456 cl. 25.4: e_min = l/500 + D/30, subject to a minimum of 20 mm.
- IS 456 cl. 26.5.3.1: longitudinal steel not less than 0.8% nor more than 6% of gross area (about 4% recommended as a practical maximum); at least 6 bars in a circular column.
- IS 456 cl. 26.5.3.2: tie diameter ≥ φ/4 and 6 mm; pitch ≤ least lateral dimension, 16φ and 300 mm.
- IS 456 Table 18: partial safety factor 1.5 for dead load plus imposed load at the limit state of collapse.