The given figure shows the shear force diagram for a beam ABCDEF. The beam has hinge support at A and at one more point. Draw the load diagram and bending moment diagram (BMD) for this beam, indicating the shape of BMD between two successive points. Also show the point of contraflexure (if any) :
[Figure, described in words: points A, B, C, D, E, F along the beam with AC = 4 m, CD = 3 m, DE = 2 m and EF = 2 m (B lies between A and C, where the diagram crosses the base line). The shear force ordinate is 10 kN below the base line at A and rises in a straight line through zero at B to 2 kN above the base line at C; it stays at 2 kN above the line from C to D; at D it jumps up to 7 kN above the line and stays at 7 kN from D to E; at E it drops to 2 kN below the line and stays at 2 kN below the line from E to F.]
20 marks · directive: Draw
The core of a good answer
Reading the SFD as a gravity-loaded beam: supports at A (10 kN up) and E (9 kN up), a uniformly distributed load of 3 kN/m over AC, 5 kN at D and 2 kN at the free end F; the BMD is parabolic on AC with maximum 16.67 kN·m at B (3.33 m from A), linear to 16 kN·m at C, 10 kN·m at D, −4 kN·m at E and zero at F, with contraflexure 8.43 m from A.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
The question reverses the usual procedure: load is inferred from the SFD (a sloping line means distributed load, a vertical jump means a concentrated force), then moments are found from the area of the SFD or by statics. The plotted sign convention is fixed by the requirement that loads act downwards and supports push upwards; with that reading every jump and slope is consistent.
Answer outline
Introduction
Convention adopted (it is the one that makes the given SFD a beam with downward loads): an upward force produces a downward step in the plotted diagram and a downward load an upward step; sagging moment positive. Under the more common convention (positive shear up on the left) the same diagram would mean all forces act the other way, with upward loads and downward support reactions, so the reading adopted is the one consistent with hinge supports carrying downward loads; the BMD shape and magnitudes are the same either way, only the signs flip.
Step 1: Loads from the SFD
- At A: step of 10 kN below the line: upward reaction R_A = 10 kN (hinge support)
- A to C: straight slope of 12 kN over 4 m: uniformly distributed load w = 3 kN/m downward over AC (total 12 kN); zero shear at B, 10/3 = 3.33 m from A
- C to D: constant, no load
- At D: step of 5 kN (2 to 7): 5 kN downward point load
- At E: step of 9 kN (7 to −2): upward reaction R_E = 9 kN (the second hinge support)
- At F: closing step of 2 kN: 2 kN downward point load at the free end; EF is an overhang
Step 2: Equilibrium check
- ΣV: 10 + 9 − 12 − 5 − 2 = 0
- ΣM_A: 9 × 9 − 12 × 2 − 5 × 7 − 2 × 11 = 81 − 81 = 0
Step 3: Bending moments (x from A)
- 0 ≤ x ≤ 4: M = 10x − 1.5x² (parabola); M_B (x = 3.33) = 16.67 kN·m maximum; M_C = 16 kN·m
- 4 ≤ x ≤ 7: M = 24 − 2x (straight line); M_D = 10 kN·m
- 7 ≤ x ≤ 9: M = 59 − 7x (straight line); M_E = −4 kN·m (hogging)
- 9 ≤ x ≤ 11: M = −2(11 − x) (straight line); M_F = 0
Step 4: Point of contraflexure
- 59 − 7x = 0 gives x = 8.43 m from A (1.43 m from D, 0.57 m from E)
Step 5: Shape of the BMD
- A to C: second degree curve (parabola), maximum at B where shear is zero
- C to D, D to E, E to F: straight lines, slopes equal to the shears 2, 7 and 2 kN
- Sagging from A to the contraflexure point, hogging over the support E and the overhang
Conclusion
Load diagram: R_A = 10 kN, R_E = 9 kN, 3 kN/m over AC, 5 kN at D, 2 kN at F. BMD peaks at +16.67 kN·m at B and −4 kN·m at E, with one contraflexure point 8.43 m from A.
Examples and data to cite
- Equilibrium of the inferred load diagram: ΣV = 10 + 9 − 12 − 5 − 2 = 0 and ΣM_A = 9 × 9 − 12 × 2 − 5 × 7 − 2 × 11 = 0, which confirms the reading of the SFD.
- Moment check from the area of the SFD: from A to B the area is −½ × 10 × 3.33 = −16.67 kN·m in the plotted sign, giving 16.67 kN·m sagging at B; from B to E the areas add to 20.67 kN·m the other way, giving −4 kN·m at E.
Facts to remember
- The slope of the shear diagram equals the distributed load intensity and the slope of the moment diagram equals the shear: a linear SFD means uniform load and a parabolic BMD; a constant SFD means no load and a linear BMD.
- A vertical step in the SFD equals a concentrated force or reaction at that point.
- Where the shear diagram crosses zero, the moment diagram has a local maximum or minimum.
- The change in bending moment between two sections equals the area of the SFD between them.