Develop the stiffness matrix for the beam element AB with respect to the coordinates ① and ② as shown in the figure. Take modulus of elasticity and moment of inertia of beam section as E and I respectively :
[Figure, described in words: a cantilever AB of length l = 2 m, fixed at A on the left and free at B on the right. Coordinate ① is a vertical (downward) translation at B and coordinate ② is a clockwise rotation at B.]
10 marks · directive: Develop
The core of a good answer
With ① = downward translation and ② = clockwise rotation at B, K = EI[[12/l³, −6/l²], [−6/l², 4/l]]; for l = 2 m, K = EI[[1.5, −1.5], [−1.5, 2.0]].
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
The stiffness matrix is built column by column: give a unit displacement at one coordinate with the other held at zero, and find the forces needed at both coordinates. The signs of the off-diagonal terms depend on the chosen directions, which the answer must follow from the figure.
Answer outline
Introduction
Cantilever fixed at A. k_ij = force at coordinate i due to unit displacement at coordinate j, others zero. Standard fixed-fixed beam results for end translation and end rotation.
Step 1: Column 1, unit downward displacement at B (θ_B = 0)
- Both ends fixed against rotation, relative translation Δ = 1: end shear 12EI/l³, end moments 6EI/l²
- Force at ① (downward) needed: k₁₁ = 12EI/l³
- The beam tends to rotate clockwise at B; to hold θ_B = 0 an anticlockwise moment is needed: k₂₁ = −6EI/l²
Step 2: Column 2, unit clockwise rotation at B (Δ_B = 0)
- Moment at B: k₂₂ = 4EI/l (clockwise)
- Force at B to keep Δ_B = 0: 6EI/l² acting upward, so k₁₂ = −6EI/l²
Step 3: Assemble
- K = [[12EI/l³, −6EI/l²], [−6EI/l², 4EI/l]] (symmetric, k₁₂ = k₂₁ by Maxwell's reciprocal theorem)
Step 4: Substitute l = 2 m
- 12/l³ = 1.5, 6/l² = 1.5, 4/l = 2.0
- K = EI[[1.5, −1.5], [−1.5, 2.0]] (units kN/m, kN, kN·m with EI in kN·m²)
Step 5: Check by flexibility
- Flexibility of a cantilever tip: f₁₁ = l³/3EI, f₂₂ = l/EI, f₁₂ = f₂₁ = l²/2EI with signs for down and clockwise both positive (a tip load downward gives clockwise rotation).
- F⁻¹ = (EI/l⁴ × 12)[[l, −l²/2], [−l²/2, l³/3]] gives the same K, confirming the signs.
Conclusion
K = EI[[1.5, −1.5], [−1.5, 2.0]]; it is symmetric and positive definite (determinant = EI² × 0.75 > 0).
Examples and data to cite
- With upward translation and anticlockwise rotation as positive, the off-diagonal terms remain negative for the right-hand end of an element.
- Numerical check by inversion of the flexibility matrix for l = 2 m: F = (1/EI)[[8/3, 2], [2, 2]], and F⁻¹ = EI[[1.5, −1.5], [−1.5, 2.0]].
Facts to remember
- Stiffness coefficient k_ij: force at i for unit displacement at j with all other coordinates restrained.
- Fixed-fixed member: unit relative end translation gives end shears 12EI/l³ and end moments 6EI/l²; unit end rotation gives 4EI/l at the near end and 2EI/l at the far end (checked by inverting the cantilever flexibility matrix).
- The stiffness relation can be inverted to give the flexibility matrix for the same coordinates, and vice versa.
- The stiffness matrix is square and symmetric.