The shrinkage limit test was conducted in a laboratory and the following results were obtained :
Initial mass of saturated clay = 45.0 g
Final mass of dry clay pat = 31.2 g
Initial volume of soil in saturated state = 24.8 cc
Final volume of dry clay pat = 16.1 cc
Determine the following properties of the soil, if the soil is at water content of 28.5% :
(i) Shrinkage limit
(ii) Shrinkage ratio
(iii) Specific gravity of soil solids
(iv) Maximum volumetric shrinkage
(v) Linear shrinkage
10 marks · directive: Determine
The core of a good answer
Shrinkage limit = 16.35%, shrinkage ratio = 1.94, specific gravity of solids = 2.84, volumetric shrinkage from 28.5% water content to the shrinkage limit = 23.6%, and linear shrinkage = 6.8%.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
The question applies the standard shrinkage factor relations. The shrinkage limit comes from the initial water content and the volume lost on drying; shrinkage ratio from the dry mass and dry volume; specific gravity from these two; volumetric and linear shrinkage are then computed for drying from the stated field water content of 28.5% down to the shrinkage limit.
Answer outline
Introduction
Given: M1 = 45.0 g (saturated), Md = 31.2 g, V1 = 24.8 cm³, Vd = 16.1 cm³, ρw = 1 g/cm³, field water content w = 28.5%.
Step 1: Initial water content
- w1 = (M1 − Md)/Md = (45.0 − 31.2)/31.2 = 0.4423 = 44.23%
Step 2: Shrinkage limit
- ws = w1 − (V1 − Vd)ρw/Md
- = 0.4423 − (24.8 − 16.1)/31.2 = 0.4423 − 0.2788 = 0.1635
- Shrinkage limit ws = 16.35%
Step 3: Shrinkage ratio
- SR = Md/(Vd ρw) = 31.2/16.1 = 1.938 (equal to the dry density in g/cm³)
Step 4: Specific gravity of solids
- G = 1/(1/SR − ws) = 1/(0.5160 − 0.1635) = 1/0.3525 = 2.84
Step 5: Volumetric shrinkage (from 28.5% to the shrinkage limit)
- VS = SR (w − ws) = 1.938 × (28.5 − 16.35) = 23.55%
- This is the maximum volume change the soil can undergo when it dries from 28.5%, since no further volume change occurs below the shrinkage limit.
Step 6: Linear shrinkage
- LS = 100 [1 − (100/(VS + 100))^(1/3)]
- = 100 [1 − (100/123.55)^(1/3)] = 100 (1 − 0.9319) = 6.81%
Conclusion
ws = 16.35%, SR = 1.94, G = 2.84, VS = 23.6% and LS = 6.8%. Check: with G = 2.84, the dry pat volume of solids = 31.2/2.84 = 10.99 cm³ and water at ws fills 0.1635 × 31.2 = 5.10 cm³, total 16.09 cm³, matching Vd = 16.1 cm³.
Examples and data to cite
- ASTM D4943 is named as the test standard for the shrinkage limit.
Facts to remember
- Shrinkage limit: water content below which further loss of moisture causes no reduction in volume.
- ws = w1 − (V1 − Vd)ρw/Md; SR = Md/(Vd ρw); G = 1/(1/SR − ws).
- Volumetric shrinkage VS = SR (w1 − ws); linear shrinkage LS = 100[1 − (100/(VS + 100))^(1/3)].
- A pat at the shrinkage limit is fully saturated, so the water at ws just fills the voids of the dry pat.