For the circuit shown below, if the power loss in 1 Ω resistor is 16 W, find the value of k in the dependent source using nodal method :
[Figure, described in words: a 10 A current source on the left, arrow pointing up, drives current into the top-left node V_A. A 2 Ω resistor connects V_A to the bottom (reference) line, with current i₀ marked flowing down through it. From V_A, a 1 Ω resistor in series with a dependent voltage source k·i₀ (minus terminal on the left, plus terminal on the right) runs along the top to node V_B. A 5 Ω resistor connects V_B to the reference line, and a 20 V voltage source (plus terminal at the top) is connected between V_B and the reference line on the right.]
10 marks · directive: Find
The core of a good answer
k = 2 (V/A) for the intended case where 4 A flows through the 1 Ω resistor from V_A towards V_B; then V_A = 12 V, V_B = 20 V and i₀ = 6 A. (If the 4 A were taken in the opposite direction, k = −6/7 would also give 16 W.)
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
A nodal analysis problem with a current controlled voltage source. The 20 V source fixes V_B directly, the power in the 1 Ω resistor fixes the magnitude of the branch current, and one KCL equation at V_A plus the KVL relation across the dependent source then give k. A good answer notes that the 5 Ω resistor does not affect the result, because it sits across an ideal voltage source.
Answer outline
Introduction
Take the bottom line as reference. Given: 10 A source into V_A, 2 Ω from V_A to reference (current i₀ = V_A/2), branch V_A to V_B made of 1 Ω and the source k·i₀ (rising from left to right), 5 Ω and 20 V across V_B.
Step 1: Fix V_B and the 1 Ω current
- The 20 V source is directly across V_B and reference, so V_B = 20 V.
- P(1 Ω) = i₁² × 1 = 16 W, so |i₁| = 4 A, where i₁ is the current from V_A to V_B through the 1 Ω resistor.
Step 2: KCL at node V_A
- 10 = V_A/2 + i₁
- With i₁ = +4 A: V_A/2 = 6, so V_A = 12 V and i₀ = V_A/2 = 6 A.
Step 3: Branch equation across the dependent source
- Going from V_A to V_B: V_B = V_A − 1 × i₁ + k i₀
- 20 = 12 − 4 + 6k
- 6k = 12, so k = 2 V/A
Step 4: The other sign (for completeness)
- With i₁ = −4 A: V_A/2 = 14, V_A = 28 V, i₀ = 14 A
- 20 = 28 + 4 + 14k gives k = −12/14 = −6/7 ≈ −0.857 V/A
- Both values satisfy the stated data; the answer above takes the 1 Ω current as flowing from V_A towards V_B, which gives k = 2, and the answer should state this assumed direction.
Step 5: Check
- With k = 2: k i₀ = 12 V, drop across 1 Ω = 4 V, so V_B = 12 − 4 + 12 = 20 V, as required.
- Current in 5 Ω = 20/5 = 4 A; the 20 V source supplies 4 − 4 = 0 A net into V_B from its own side (the 4 A arriving through the 1 Ω branch flows into the 5 Ω resistor).
Conclusion
k = 2 V/A (a transresistance, since it multiplies a current to give a voltage). The power check P = 4² × 1 = 16 W holds.
Examples and data to cite
- Ideal voltage source across a node: in nodal analysis that node voltage is known, so the node needs no KCL equation (a standard simplification in textbook nodal analysis).
- Supernode technique: needed only when a voltage source sits between two non-reference nodes whose voltages are both unknown; here V_B is known, so a plain branch equation suffices.
Facts to remember
- KCL: the algebraic sum of currents leaving a node is zero.
- Power in a resistor P = I²R, so a known power fixes only the magnitude of the current, not its direction.
- A current controlled voltage source k·i₀ has k in ohms (V/A).
- An element in parallel with an ideal voltage source does not change any other branch current or voltage in the circuit.