For the circuit shown below, find the value of R, if the power supplied by both the sources is equal :
[Figure, described in words: a 100 V voltage source (plus terminal at the top) on the left; its top terminal connects through a 5 Ω resistor to node 1. A 10 Ω resistor connects node 1 to the bottom (reference) line. A 20 Ω resistor connects node 1 to node 2. The resistor R connects node 2 to the reference line, and a 10 A current source on the right, arrow pointing up, drives current into node 2 from the reference line.]
10 marks · directive: Find
The core of a good answer
R = 20/3 ≈ 6.67 Ω: the equal power condition together with KCL gives V₁ = V₂ = 200/3 ≈ 66.67 V, so no current flows in the 20 Ω resistor, the whole 10 A goes through R, and each source supplies 666.7 W.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
Nodal analysis with an extra condition. Two node voltages and R are unknown; the two KCL equations and the equal power equation supply three equations. The candidate must use the correct sign convention for power supplied by each source.
Answer outline
Introduction
Take the bottom line as reference; V₁ at the junction of 5 Ω, 10 Ω and 20 Ω, V₂ at the junction of 20 Ω, R and the current source.
Step 1: Power supplied by each source
- Voltage source current (out of its + terminal) I_s = (100 − V₁)/5; power P₁ = 100 × (100 − V₁)/5 = 20(100 − V₁)
- Current source pushes 10 A into node 2, so power P₂ = 10 × V₂
- P₁ = P₂ gives V₂ = 200 − 2V₁
Step 2: KCL at node 1
- (100 − V₁)/5 = V₁/10 + (V₁ − V₂)/20
- Multiply by 20: 400 − 4V₁ = 2V₁ + V₁ − V₂, i.e. 7V₁ − V₂ = 400
Step 3: Solve
- 7V₁ − (200 − 2V₁) = 400, so 9V₁ = 600, V₁ = 66.67 V
- V₂ = 200 − 133.33 = 66.67 V
Step 4: KCL at node 2 gives R
- 10 + (V₁ − V₂)/20 = V₂/R; with V₁ = V₂ the 20 Ω current is zero
- R = 66.67/10 = 6.667 Ω = 20/3 Ω
Step 5: Check
- I_s = (100 − 66.67)/5 = 6.667 A; P₁ = 666.7 W; P₂ = 10 × 66.67 = 666.7 W
- Absorbed: 5 Ω: 6.667² × 5 = 222.2 W; 10 Ω: 66.67²/10 = 444.4 W; R: 10² × 6.667 = 666.7 W; total 1333.3 W = P₁ + P₂
Conclusion
R = 20/3 Ω ≈ 6.67 Ω, with both sources delivering 666.7 W and the total absorbed power 1333.3 W balancing.
Examples and data to cite
- Power balance (Tellegen's theorem in its simplest form) is the standard check for any power question in circuit analysis.
- In nodal analysis the 10 A current source needs no extra unknown, because its current enters the KCL equation at node 2 directly.
Facts to remember
- Power supplied by a source = V × I with I leaving the positive terminal (passive sign convention reversed).
- KCL at each non-reference node.
- Sum of powers supplied equals sum of powers absorbed (Tellegen's theorem).
- Zero voltage across a resistor means zero current through it.