For the circuit shown below, steady state is achieved with switch K open. At t = 0, switch K is closed. Find the time expression of current in R_L. Also find its initial and final values :
[Figure, described in words: a 50 V source (plus terminal at the top) on the left; its top terminal connects through a 5 Ω resistor to node A. From node A a branch of a 20 Ω resistor in series with a 1 H inductor goes down to the bottom (return) line. From node A the switch K (closing at t = 0) connects to a load resistor R_L = 20 Ω, whose other end is on the bottom line.]
10 marks · directive: Find
The core of a good answer
i_L(0) = 2 A and after closing i_L(t) = 5/3 + (1/3)e^{−24t} A, so the load current is i_RL(t) = 5/3 − (1/15)e^{−24t} ≈ 1.667 − 0.0667e^{−24t} A for t > 0, with initial value 1.6 A and final value 1.667 A (time constant 1/24 s ≈ 41.7 ms).
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
A first order RL transient. The inductor current is continuous at t = 0; after switching, the Thevenin equivalent seen by the inductor branch gives the time constant and final value, and the load current follows from the node voltage.
Answer outline
Introduction
Before t = 0 (K open, steady state) the inductor is a short. After t = 0 the 50 V source with 5 Ω, in parallel with R_L = 20 Ω, feeds the 20 Ω + 1 H branch.
Step 1: Initial inductor current
- i_L(0⁻) = 50/(5 + 20) = 2 A = i_L(0⁺)
Step 2: Thevenin equivalent seen by the inductor branch (t > 0)
- V_th = 50 × 20/(5 + 20) = 40 V
- R_th = 5 ∥ 20 = 4 Ω
- Total resistance in the inductor loop = 4 + 20 = 24 Ω; τ = L/R = 1/24 s
Step 3: Inductor current
- i_L(∞) = 40/24 = 5/3 A
- i_L(t) = 5/3 + (2 − 5/3)e^{−24t} = 5/3 + (1/3)e^{−24t} A
Step 4: Node voltage and load current
- v_A = 20 i_L + L di_L/dt = 20(5/3 + (1/3)e^{−24t}) − 8e^{−24t} = 100/3 − (4/3)e^{−24t} V
- i_RL(t) = v_A/20 = 5/3 − (1/15)e^{−24t} A, t > 0
Step 5: Initial and final values, with check
- i_RL(0⁺) = 5/3 − 1/15 = 1.6 A (direct check: KCL at A with i_L = 2 A gives (50 − v_A)/5 = 2 + v_A/20, so v_A = 32 V and i_RL = 1.6 A)
- i_RL(∞) = 5/3 ≈ 1.667 A (inductor a short: 20 ∥ 20 = 10 Ω, total 15 Ω, source current 10/3 A shared equally)
- i_RL(0⁻) = 0 because K is open, so the load current jumps to 1.6 A and then rises slowly to 1.667 A.
Conclusion
i_RL(t) = 1.667 − 0.0667e^{−24t} A; initial 1.6 A, final 1.667 A, τ = 41.7 ms.
Examples and data to cite
- The same Thevenin plus continuity method applies to relay coils and solenoid circuits switched by contacts in power and control panels.
- Standard first order response: x(t) = x(∞) + [x(0⁺) − x(∞)]e^{−t/τ}.
Facts to remember
- Inductor current cannot change instantaneously: i_L(0⁺) = i_L(0⁻).
- In DC steady state an inductor behaves as a short circuit.
- Time constant of an RL circuit τ = L/R_eq, R_eq being the Thevenin resistance seen by L.
- First order response x(t) = x(∞) + [x(0⁺) − x(∞)]e^{−t/τ}.