Find the y-parameters of the two-port network shown below :
[Figure, described in words: port 1 (terminals 1 and 1′, voltage V₁, current I₁ entering terminal 1) and port 2 (terminals 2 and 2′, voltage V₂, current I₂ entering terminal 2) share a common bottom line 1′ to 2′. A 1 Ω resistor is connected from terminal 1 to the bottom line. A 2 Ω series resistor connects terminal 1 to the node at terminal 2. At the terminal 2 node, a 2 Ω resistor goes to the bottom line and a dependent current source of value 3I₁ also goes to the bottom line, its arrow pointing down (current 3I₁ flowing from the terminal 2 node to the bottom line).]
10 marks · directive: Find
Answer
The core of a good answer
y₁₁ = 1.5 S, y₁₂ = −0.5 S, y₂₁ = 4 S, y₂₂ = −0.5 S, i.e. I₁ = 1.5V₁ − 0.5V₂ and I₂ = 4V₁ − 0.5V₂; the network is not reciprocal (y₁₂ ≠ y₂₁) because of the dependent source.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
Write the two node equations of the network directly in the admittance form I = YV, eliminating the controlling current I₁ of the dependent source. Short circuit tests give the same result.
Answer outline
Introduction
Node 1 is terminal 1 (voltage V₁), node 2 is terminal 2 (voltage V₂), both measured from the common line.
Step 1: KCL at node 1
- I₁ = V₁/1 + (V₁ − V₂)/2
- I₁ = 1.5V₁ − 0.5V₂
Step 2: KCL at node 2
- I₂ = (V₂ − V₁)/2 + V₂/2 + 3I₁
- Substitute I₁: I₂ = −0.5V₁ + V₂ + 3(1.5V₁ − 0.5V₂)
- I₂ = 4V₁ − 0.5V₂
Step 3: Read off the y-parameters
- y₁₁ = I₁/V₁ with V₂ = 0: 1.5 S
- y₁₂ = I₁/V₂ with V₁ = 0: −0.5 S
- y₂₁ = I₂/V₁ with V₂ = 0: 4 S
- y₂₂ = I₂/V₂ with V₁ = 0: −0.5 S
Step 4: Check by a short circuit test
- V₂ = 0: I₁ = V₁(1 + 1/2) = 1.5V₁; current in the 2 Ω series resistor towards node 2 = V₁/2; I₂ = 3I₁ − V₁/2 = 4.5V₁ − 0.5V₁ = 4V₁, agreeing with y₂₁ = 4 S.
- V₁ = 0: I₁ = −V₂/2 and I₂ = V₂/2 + V₂/2 + 3(−V₂/2) = −0.5V₂, agreeing with y₂₂ = −0.5 S.
Conclusion
[y] = [[1.5, −0.5], [4, −0.5]] S. The negative y₂₂ reflects the active dependent source, and y₁₂ ≠ y₂₁ shows non-reciprocity.
Examples and data to cite
- A two-port network in general is not reciprocal if it contains active components such as generators or transistors; here the dependent source 3I₁ plays that role.
- For a passive reciprocal network y₁₂ = y₂₁; any dependent source generally breaks this.
Facts
Facts to remember
- Definition: I₁ = y₁₁V₁ + y₁₂V₂; I₂ = y₂₁V₁ + y₂₂V₂.
- y-parameters are short circuit admittance parameters (measured with the other port shorted).
- Reciprocity condition for y-parameters: y₁₂ = y₂₁.
- Controlling variables of dependent sources must be expressed in terms of the port variables before reading off parameters.