For the following circuit given in Fig. (1) below, the diode has the I-V characteristic in forward direction as shown in Fig. (2) :
[Fig. (1), described in words: a diamond (bridge) of four resistors with top node T, bottom node B, left node L and right node R: 2·0 Ω between L and T, 6·0 Ω between T and R, 8·0 Ω between L and B, and 8·0 Ω between B and R. A diode is connected from T to B, anode at T and cathode at B, with the current i_d marked flowing downwards. A 20 V battery is connected between L and R below the bridge (as drawn, its longer plate, the positive terminal, is on the side connected to L).]
[Fig. (2), described in words: forward characteristic i_d against v_d; i_d = 0 up to v_d = 0·7 V, then a straight line rising to i_d = 1·0 A at v_d = 0·9 V.]
Find the (i) diode current, (ii) diode power loss and (iii) power supplied by the source.
20 marks · directive: Find
The core of a good answer
The diode is a 0.7 V source in series with 0.2 Ω; the bridge's Thevenin equivalent across the diode is 5 V behind 5.5 Ω, so (i) i_d = 4.3/5.7 ≈ 0.754 A (v_d ≈ 0.851 V), (ii) diode loss ≈ 0.642 W, and (iii) the 20 V source supplies ≈ 3.94 A, i.e. ≈ 78.8 W.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
A piecewise linear diode model inside an unbalanced bridge. The candidate must first check that the diode is forward biased (open circuit voltage across it greater than 0.7 V), model it as V_γ plus r_f, use Thevenin's theorem across the diode, and then go back to the full circuit for the source power.
Answer outline
Introduction
Take node R as reference, so V_L = 20 V (polarity as read from the figure). Diode model from Fig. (2): v_d = 0.7 + r_f i_d for i_d > 0, with r_f = (0.9 − 0.7)/1.0 = 0.2 Ω.
Step 1: Check the diode state (diode removed)
- V_T = 20 × 6/(2 + 6) = 15 V; V_B = 20 × 8/(8 + 8) = 10 V
- Open circuit voltage V_TB = 5 V > 0.7 V, so the diode conducts.
Step 2: Thevenin equivalent across T and B
- V_th = 5 V
- R_th = (2 ∥ 6) + (8 ∥ 8) = 1.5 + 4 = 5.5 Ω (source shorted, L and R merge)
Step 3: Diode current and voltage (i)
- i_d = (V_th − 0.7)/(R_th + r_f) = 4.3/5.7 = 0.7544 A
- v_d = 0.7 + 0.2 × 0.7544 = 0.8509 V (on the linear segment, below 0.9 V and 1 A, so the model is consistent)
Step 4: Diode power loss (ii)
- P_d = v_d i_d = 0.8509 × 0.7544 = 0.642 W
- (= 0.7 × 0.7544 + 0.2 × 0.7544² = 0.528 + 0.114 W)
Step 5: Node voltages and source power (iii)
- KCL at T: (20 − V_T)/2 = V_T/6 + i_d; KCL at B: (20 − V_B)/8 + i_d = V_B/8
- Solving: V_T = 13.868 V, V_B = 13.018 V (V_T − V_B = 0.851 V = v_d, consistent)
- Source current I_s = (20 − 13.868)/2 + (20 − 13.018)/8 = 3.066 + 0.873 = 3.939 A
- P_source = 20 × 3.939 = 78.77 W
Step 6: Power balance check
- Resistor losses: 2 Ω: 18.80 W; 6 Ω: 32.05 W; 8 Ω (L to B): 6.09 W; 8 Ω (B to R): 21.18 W; diode 0.64 W
- Total = 78.77 W, equal to the source power.
Conclusion
i_d ≈ 0.754 A, diode loss ≈ 0.642 W, source power ≈ 78.8 W (I_s ≈ 3.94 A). If the battery polarity were the reverse, V_TB would be −5 V and the diode would be off, so the polarity read from the figure matters.
Examples and data to cite
- Piecewise linear (constant voltage drop plus resistance) diode models are the standard textbook approximation.
- Unbalanced Wheatstone bridge with a detector across the diagonal: the same Thevenin approach gives the galvanometer current.
Facts to remember
- Piecewise linear diode: v_d = V_γ + r_f i_d for v_d > V_γ, i_d = 0 otherwise; here V_γ = 0.7 V, r_f = 0.2 Ω.
- Thevenin's theorem: any linear two terminal network is equivalent to V_th in series with R_th.
- Check the assumed diode state against the result (current positive, operating point on the assumed segment).
- Power balance: power supplied equals the sum of the powers absorbed.