For the circuit shown in the figure below, the two transistors Q₁ and Q₂ have β₁ = 35 and β₂ = 30. The resistance R₂ is variable. The output voltage V_o across resistance R_o is +5·0 V. If the voltage V_CC is kept at +12·0 V, find the value of R₂. Derive any formula used. Assume V_BE = 0·7 V for both the transistors :
[Figure, described in words: R₁ = 100K is connected from V_CC = +12·0 V to the base of Q₁, and the variable resistor R₂ from the base of Q₁ to ground, forming a divider. The collectors of Q₁ and Q₂ are both connected to V_CC. The emitter of Q₁ drives the base of Q₂ (Darlington connection). The emitter of Q₂ is connected through R_o = 1 kΩ to ground, and V_o = +5·0 V is taken at the emitter of Q₂.]
10 marks · directive: Find
The core of a good answer
I_E2 = 5 V/1 kΩ = 5 mA, so I_B2 = I_E1 = 5/31 = 0.1613 mA and I_B1 = 0.1613/36 = 4.48 μA; the base of Q₁ sits at 5 + 0.7 + 0.7 = 6.4 V, R₁ carries (12 − 6.4)/100 k = 56 μA, R₂ carries 51.52 μA, so R₂ = 6.4 V/51.52 μA ≈ 124.2 kΩ.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
A DC bias problem on a Darlington emitter follower. Work backwards from the known output voltage through the emitter and base currents of both transistors to the divider, deriving I_E = (β + 1)I_B and the Darlington gain on the way.
Answer outline
Introduction
Active region for both transistors (collectors at 12 V, emitters lower). Known: V_o = 5 V, R_o = 1 kΩ, V_BE = 0.7 V, β₁ = 35, β₂ = 30, R₁ = 100 kΩ.
Step 1: Derive I_E = (β + 1)I_B
- KCL for a BJT: I_E = I_B + I_C, and I_C = βI_B in the active region
- So I_E = (β + 1)I_B; for the pair, I_E2 = (β₂ + 1)I_B2 = (β₂ + 1)I_E1 = (β₂ + 1)(β₁ + 1)I_B1
- Overall current gain I_E2/I_B1 = (β₁ + 1)(β₂ + 1) = 36 × 31 = 1116 (≈ β₁β₂ for large β)
Step 2: Emitter and base currents
- I_E2 = V_o/R_o = 5/1000 = 5 mA
- I_B2 = I_E1 = 5/31 = 0.16129 mA
- I_B1 = 0.16129/36 = 4.480 μA
Step 3: Base voltage of Q₁
- V_B1 = V_o + V_BE2 + V_BE1 = 5 + 0.7 + 0.7 = 6.4 V
Step 4: Divider currents
- I_R1 = (12 − 6.4)/100 kΩ = 56.0 μA
- KCL at the base of Q₁: I_R2 = I_R1 − I_B1 = 56.0 − 4.48 = 51.52 μA
Step 5: Value of R₂
- R₂ = V_B1/I_R2 = 6.4/(51.52 × 10⁻⁶) = 124.2 kΩ
- Check active region: V_CE1 = 12 − 5.7 = 6.3 V and V_CE2 = 12 − 5 = 7 V, both well above saturation.
Conclusion
R₂ ≈ 124 kΩ. Ignoring the base current would give R₂ = 6.4/56 μA ≈ 114.3 kΩ, so the 4.48 μA base current matters at this β.
Examples and data to cite
- The Darlington pair (invented in 1953 by Sidney Darlington) gives a current gain of roughly β₁β₂ and a base emitter drop of about twice that of one transistor (about 1.3 V for silicon).
- Because the overall gain is 1116, the base current drawn from the divider is only 4.48 μA, far less than the 5 mA load current; so the Darlington stage loads the divider only lightly.
Facts to remember
- BJT active region: I_C = βI_B, I_E = (β + 1)I_B.
- Darlington pair: overall gain (β₁ + 1)(β₂ + 1) ≈ β₁β₂; total V_BE ≈ 2 × 0.7 V.
- KCL at the divider node: I_R1 = I_R2 + I_B1.
- Ohm's law at the emitter: I_E2 = V_o/R_o.