A single-phase, full-wave bridge diode rectifier supplied from 240 V, 50 Hz AC source is feeding a resistive load R_L = 100 Ω as shown in the figure below. Due to fault in the diode D₂, it behaves like a resistance of 1 kΩ. Sketch the load voltage, load current and source current waveforms under faulty condition. Also calculate the load average voltage and r.m.s. source current under this situation :
[Figure, described in words: a bridge with a left leg and a right leg between a top rail and a bottom rail. Left leg: D₁ from the left midpoint (anode) to the top rail (cathode), and D₄ from the bottom rail (anode) to the left midpoint (cathode). Right leg: D₃ from the right midpoint (anode) to the top rail (cathode), and D₂ from the bottom rail (anode) to the right midpoint (cathode). One source terminal goes to the left midpoint and the other to the right midpoint. R_L = 100 Ω is connected between the top rail and the bottom rail.]
10 marks · directive: Sketch
The core of a good answer
With ideal healthy diodes, in the half cycle when D₁ conducts the load is in series with the 1 kΩ fault, so v_L = v_s/11 (peak 30.9 V); in the other half D₃ and D₄ conduct and v_L = |v_s| (peak 339.4 V) while the 1 kΩ sits directly across the source. Average load voltage = (V_m/π)(12/11) ≈ 117.9 V and r.m.s. source current ≈ 1.87 A.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
A fault analysis of a bridge rectifier: identify the conducting pair in each half cycle, see how a resistive D₂ changes each path, and then integrate over a cycle. The sketches must show the unequal half cycles and the distorted source current.
Answer outline
Introduction
v_s = V_m sin ωt with V_m = 240√2 = 339.41 V; let v_s be positive when the left midpoint is positive. Healthy diodes are ideal. Normal pairs: D₁, D₂ in one half cycle and D₃, D₄ in the other.
Step 1: Positive half cycle (left midpoint positive)
- D₁ conducts: top rail = left midpoint. Current flows down through R_L to the bottom rail, then through the 1 kΩ (faulty D₂) to the right midpoint and back to the source.
- D₃ and D₄ are reverse biased.
- i_s = i_L = v_s/(100 + 1000) = v_s/1100; peak 0.309 A
- v_L = 100 v_s/1100 = v_s/11; peak 30.86 V
Step 2: Negative half cycle (right midpoint positive)
- D₃ and D₄ conduct: top rail = right midpoint, bottom rail = left midpoint, so v_L = |v_s|; peak 339.4 V; i_L peak 3.394 A
- The 1 kΩ (faulty D₂) is now connected between the bottom rail (left midpoint potential) and the right midpoint, i.e. directly across the source, drawing |v_s|/1000 (peak 0.339 A) that bypasses the load.
- |i_s| = |v_s|/100 + |v_s|/1000 = 0.011|v_s|; peak 3.734 A
Step 3: Average load voltage
- V_avg = (1/2π)[∫ from 0 to π of (V_m/11) sin θ dθ + ∫ from π to 2π of V_m |sin θ| dθ]
- V_avg = (1/2π)(2V_m/11 + 2V_m) = (V_m/π)(12/11)
- V_avg = (339.41/π) × 1.0909 = 117.86 V (against 216.1 V for a healthy bridge); average load current 1.179 A
Step 4: r.m.s. source current
- I_rms² = ½[(V_m/1100)²/2 + (0.011V_m)²/2] = ½[(240/1100)² + (0.011 × 240)²]
- I_rms² = ½[0.0476 + 6.970] = 3.509, so I_rms = 1.873 A
Step 5: Waveform sketches (describe)
- Load voltage: unidirectional half sine humps, small (30.9 V peak) in the half cycle with the faulty diode, full (339.4 V peak) in the other half.
- Load current: same shape as load voltage, peaks 0.309 A and 3.394 A.
- Source current: sinusoidal half cycles of unequal size, 0.309 A peak in one direction and 3.734 A peak in the other, so it carries a DC component and even harmonics.
Conclusion
V_L(avg) ≈ 117.9 V and I_s(rms) ≈ 1.87 A; the fault makes the output nearly a half wave rectified wave and draws an asymmetric source current with a DC component of about 1.09 A.
Examples and data to cite
- A healthy single phase bridge gives V_avg = 2V_m/π = 216.1 V for 240 V r.m.s.; the drop to 117.9 V is a quick diagnostic of a degraded diode.
- Averaging the source current over a cycle gives about 1.09 A (in the direction of the large half cycle), a DC component that a healthy bridge does not draw.
Facts to remember
- Bridge rectifier: diagonally opposite diodes (D₁ with D₂, D₃ with D₄ in this figure) conduct together.
- Ideal full wave average: V_avg = 2V_m/π; half wave: V_m/π.
- r.m.s. of a sinusoidal half cycle of peak I_p over a full cycle: I_p/2.
- V_m = √2 × V_rms = 339.4 V for 240 V.