For the circuit given in the figure below, the input voltage signal is given by Vᵢₙ = 1·5 sin 62·8t + 0·5 sin 188·4t volts. Determine the output voltage expression for each input component indicating their magnitude and phases. Derive the frequency domain expression for the output voltage :
[Figure, described in words: Vᵢₙ is applied through a series capacitor C = 1·0 μF to the non-inverting (+) input of an op-amp; R₁ = 10K connects the + input to ground. The output Vₒ is fed back to the inverting (−) input through R₃ = 10K, and R₂ = 22K connects the inverting input to ground.]
10 marks · directive: Determine
The core of a good answer
The circuit is a first-order active high-pass filter, Vₒ(jω) = (1 + R₃/R₂)·jωR₁C/(1 + jωR₁C)·Vᵢₙ(jω) with pass-band gain 1·4545 and corner ω꜀ = 100 rad/s (15·9 Hz), so Vₒ = 1·160 sin(62·8t + 57·87°) + 0·642 sin(188·4t + 27·96°) V.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
The question tests recognition of an RC high-pass network followed by a non-inverting amplifier, derivation of its transfer function, and use of superposition on a two-tone sinusoidal input. Each component is treated as a phasor at its own frequency; magnitude and phase shift are read from H(jω).
Answer outline
Introduction
Given: C = 1 μF, R₁ = 10 kΩ, R₂ = 22 kΩ, R₃ = 10 kΩ, ideal op-amp. Input tones: 1·5 V at ω₁ = 62·8 rad/s (about 10 Hz) and 0·5 V at ω₂ = 188·4 rad/s (about 30 Hz).
Step 1: Voltage at the non-inverting input
- The op-amp input draws no current, so C and R₁ form a voltage divider.
- V₊(s) = R₁/(R₁ + 1/sC)·Vᵢₙ(s) = sR₁C/(1 + sR₁C)·Vᵢₙ(s)
- R₁C = 10×10³ × 1×10⁻⁶ = 0·01 s, so ω꜀ = 1/R₁C = 100 rad/s, f꜀ = 15·92 Hz
Step 2: Non-inverting gain stage
- Virtual short: V₋ = V₊ and V₋ = Vₒ·R₂/(R₂ + R₃)
- A = Vₒ/V₊ = 1 + R₃/R₂ = 1 + 10/22 = 1·4545 (3·25 dB)
Step 3: Frequency domain expression
- H(s) = Vₒ(s)/Vᵢₙ(s) = (1 + R₃/R₂)·sR₁C/(1 + sR₁C) = 1·4545·(0·01s)/(1 + 0·01s)
- H(jω) = 1·4545·j(ω/100)/(1 + jω/100)
- |H(jω)| = 1·4545·(ω/100)/√(1 + (ω/100)²); ∠H(jω) = 90° − tan⁻¹(ω/100)
Step 4: Component at ω₁ = 62·8 rad/s
- ω₁/ω꜀ = 0·628; high-pass factor = 0·628/√(1 + 0·3944) = 0·5318
- |H| = 1·4545 × 0·5318 = 0·7736; phase = 90° − 32·13° = +57·87°
- Vₒ₁ = 1·5 × 0·7736 = 1·160 V, so Vₒ₁(t) = 1·160 sin(62·8t + 57·87°) V
Step 5: Component at ω₂ = 188·4 rad/s
- ω₂/ω꜀ = 1·884; high-pass factor = 1·884/√(1 + 3·549) = 0·8833
- |H| = 1·4545 × 0·8833 = 1·2848; phase = 90° − 62·04° = +27·96°
- Vₒ₂ = 0·5 × 1·2848 = 0·642 V, so Vₒ₂(t) = 0·642 sin(188·4t + 27·96°) V
Step 6: Superposition
- Vₒ(t) = 1·160 sin(62·8t + 57·87°) + 0·642 sin(188·4t + 27·96°) V
- Vₒ(jω) = [1·4545·j0·01ω/(1 + j0·01ω)]·Vᵢₙ(jω)
Conclusion
The lower tone lies below the 100 rad/s corner and the upper tone above it, so the lower tone is attenuated more (gain 0·77) and shifted more (57·9° lead) than the upper tone (gain 1·28, 28° lead). Check: as ω → ∞ the gain tends to 1·4545 and the phase to 0°, as expected for a high-pass stage.
Examples and data to cite
- 62·8 rad/s ≈ 2π × 10 Hz and 188·4 rad/s ≈ 2π × 30 Hz, so the input is a fundamental plus a third harmonic; the filter changes the waveshape because the two tones get different gains and phase shifts.
- This topology (a passive RC high-pass section followed by a non-inverting amplifier) is a first-order active high-pass filter.
Facts to remember
- First-order RC high-pass transfer function: sRC/(1 + sRC), corner ω꜀ = 1/RC.
- Non-inverting amplifier gain = 1 + R_f/R_g (here R₃ feedback, R₂ to ground).
- A high-pass section leads the input by 90° − tan⁻¹(ω/ω꜀); the lead is 45° at ω = ω꜀.
- Superposition applies because the circuit is linear: each sinusoid is processed separately and the outputs added.