The thyristor T in the circuit shown below is turned on at t = 0, when key K is switched off. Determine the conduction time of T and the capacitor voltage after T is turned off. Given that the inductor carries an initial current of 250 A and initial capacitor voltage is zero :
[Figure, described in words: A 250 A current source (arrow pointing towards the V_s end of L) in series with key K (marked open at t = 0) is connected across the inductor L = 10 μH, so that before t = 0 it circulates 250 A through L in the direction from V_s towards T. V_s = 200 V (positive terminal at the inductor end), L, thyristor T and C = 10 μF (voltage V_C, positive at the T end) form a single series loop.]
10 marks · directive: Determine
The core of a good answer
After K opens, V_s, L, T and C form a series LC loop with ω₀ = 10⁵ rad/s and Z₀ = 1 Ω; i(t) = 250 cos ω₀t + 200 sin ω₀t falls to zero at ω₀t = 128·66°, so T conducts for about 22·46 μs and the capacitor is left charged to 200 + 320·16 = 520·16 V.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
This is a resonant commutation problem: write the series LC equations with non-zero initial inductor current, find when the current first reaches zero (the thyristor then turns off naturally), and evaluate the capacitor voltage at that instant.
Answer outline
Introduction
Given: V_s = 200 V, L = 10 μH, C = 10 μF, i(0) = I₀ = 250 A, v꜀(0) = 0. When K opens the current source is removed, and the inductor current continues through T into C.
Step 1: Circuit equations
- L di/dt + v꜀ = V_s; C dv꜀/dt = i
- ω₀ = 1/√(LC) = 1/√(10⁻¹⁰) = 10⁵ rad/s; Z₀ = √(L/C) = 1 Ω
Step 2: Solution with initial conditions
- i(t) = I₀ cos ω₀t + (V_s/Z₀) sin ω₀t = 250 cos ω₀t + 200 sin ω₀t A
- v꜀(t) = V_s(1 − cos ω₀t) + I₀Z₀ sin ω₀t = 200(1 − cos ω₀t) + 250 sin ω₀t V
- i(t) = I_p cos(ω₀t − φ), I_p = √(250² + 200²) = 320·16 A, φ = tan⁻¹(200/250) = 38·66°
Step 3: Conduction time
- T turns off when i = 0 for the first time: ω₀t − φ = 90°, so ω₀t = 128·66° = 2·2455 rad
- t_c = 2·2455/10⁵ = 22·46 μs
Step 4: Capacitor voltage at turn-off
- v꜀ = 200(1 − cos 128·66°) + 250 sin 128·66° = 200 + 125·0 + 195·2 = 520·16 V
- Equivalently v꜀ = V_s + I_pZ₀ = 200 + 320·16 = 520·16 V
Step 5: Energy check
- Energy at t = 0: ½LI₀² = ½ × 10⁻⁵ × 62500 = 0·3125 J
- Energy from source = V_s·Q = 200 × C·v꜀ = 200 × 10⁻⁵ × 520·16 = 1·0403 J
- Final capacitor energy ½Cv꜀² = 1·3528 J = 0·3125 + 1·0403 J, so energy balances
Conclusion
The thyristor conducts for about 22·5 μs and the capacitor is left at about 520 V, more than twice the supply voltage, because the stored inductor energy is also transferred to C. A numerical solution of the differential equations gives the same zero-crossing time and voltage.
Examples and data to cite
- Without initial inductor current the same circuit would charge C to exactly 2V_s = 400 V in half a period (π/ω₀ = 31·4 μs); the initial current both shortens conduction and raises the final voltage.
- A thyristor stays on until its current falls below the holding current; here the series LC loop itself drives the current to zero, so T turns off without any separate commutation circuit.
Facts to remember
- Series LC with source: i = I₀ cos ω₀t + (V_s − V꜀₀)/Z₀·sin ω₀t.
- ω₀ = 1/√(LC), characteristic impedance Z₀ = √(L/C).
- A thyristor turns off when its anode current falls below the holding current.
- Peak capacitor voltage at zero current: V_s + √((V_s − V꜀₀)² + (I₀Z₀)²).