A three-phase, star-connected, 415 V, 50 Hz, cage-type induction motor takes a starting current equal to 10 times of its no-load current magnitude. The starting torque is one-third (1/3 times) of its pull-out torque (POT), all under rated conditions. The motor takes 300 W input power at 0·2 p.f. lag with rated supply voltage and frequency. Its core loss has no hysteresis component. Find the starting current and input p.f. of the motor at 5 Hz supply voltage maintaining rated V/f ratio. Neglect stator leakage impedance and rotor current at no load. Assume linear magnetic circuit.
20 marks · directive: Find
The core of a good answer
With stator impedance neglected, T_st/T_max = 2s_m/(1 + s_m²) = 1/3 gives R₂′/X₂′ = s_m = 0·1716; fitting the rated starting current (20·87 A) gives R₂′ = 2·157 Ω and X₂′ = 12·573 Ω, and at 5 Hz with V/f constant (23·96 V per phase) the starting current is about 10·8 A at about 0·77 p.f. lag.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
The problem tests the approximate equivalent circuit with the magnetising branch at the terminals, the torque-slip relation, and how each element changes with frequency under constant V/f: reactances scale with f, rotor resistance does not, magnetising current stays the same and eddy-current loss scales with V². The starting current is taken as the total stator current (rotor plus no-load components).
Answer outline
Introduction
Per phase: V = 415/√3 = 239·60 V. No-load: I₀ = 300/(√3 × 415 × 0·2) = 2·087 A at 0·2 p.f. lag (−78·46°). Rated starting current = 10 × 2·087 = 20·87 A.
Step 1: Rotor R/X ratio from torque data
- With stator impedance neglected, T ∝ (R₂′/s)/[(R₂′/s)² + X₂′²] and s_m = R₂′/X₂′
- T_st/T_max = 2s_m/(1 + s_m²) = 1/3, so s_m² − 6s_m + 1 = 0
- s_m = 3 − 2√2 = 0·1716 (the root less than 1), rotor impedance angle θ = tan⁻¹(1/0·1716) = 80·26°
Step 2: Rotor impedance from starting current
- I_st = I₀∠−78·46° + I₂′∠−80·26°, with |I_st| = 20·87 A
- Solving: I₂′ = 18·78 A, so Z₂′ = 239·60/18·78 = 12·757 Ω
- R₂′ = 12·757 cos 80·26° = 2·157 Ω; X₂′ = 12·757 sin 80·26° = 12·573 Ω (at 50 Hz)
Step 3: Shunt branch at 5 Hz with V/f constant
- V = 239·60 × 5/50 = 23·96 V per phase (41·5 V line)
- Magnetising current I_m = V/X_m is unchanged, since both V and X_m scale by 0·1: I_m = 2·087 × 0·9798 = 2·045 A
- Core-loss component: R꜀ fixed (eddy loss ∝ V²), so I꜀ = 0·1 × (2·087 × 0·2) = 0·0417 A
- I₀(5 Hz) = 0·0417 − j2·0446 A
Step 4: Rotor current at standstill, 5 Hz
- X₂′ at 5 Hz = 1·2573 Ω, R₂′ = 2·157 Ω (s = 1)
- I₂′ = 23·96/(2·157 + j1·2573) = 9·596 A ∠−30·24° = 8·291 − j4·832 A
Step 5: Starting current and power factor at 5 Hz
- I_st = (0·0417 + 8·291) − j(2·045 + 4·832) = 8·332 − j6·877 A
- |I_st| = 10·80 A; angle −39·53°
- Input p.f. = cos 39·53° = 0·771 lag
Conclusion
At 5 Hz with rated V/f the starting current falls to about 10·8 A (about half of the 50 Hz value) while the starting power factor rises from about 0·17 to about 0·77 lag, because rotor resistance now dominates the rotor reactance.
Examples and data to cite
- A variable-frequency drive initially applies a low frequency and voltage, avoiding the high inrush current of direct-on-line starting; in this motor the starting current falls from 20·87 A at 50 Hz to 10·8 A at 5 Hz.
- At 50 Hz the same motor starts with only about 0·17 p.f., since X₂′ is nearly six times R₂′.
Facts to remember
- T_st/T_max = 2s_m/(1 + s_m²) when stator impedance is neglected; s_m = R₂′/X₂′.
- Constant V/f keeps air-gap flux and magnetising current constant (linear magnetic circuit).
- Leakage reactance ∝ f; rotor resistance independent of f (no skin effect assumed).
- Eddy-current loss ∝ (Bf)² ∝ V², so the equivalent core-loss resistance is independent of frequency.