In the 8085 microprocessor, explain the functionality of the following pins, and describe the role of the instruction decoder, stack pointer and program counter.
1. READY
2. SID
3. SOD
4. INTR
5. CLK (OUT)
10 marks · directive: Explain
The core of a good answer
READY (pin 35) lets slow memory or I/O insert wait states, SID and SOD are the serial data input and output lines handled by RIM and SIM, INTR is the externally serviced interrupt request, and CLK (OUT) makes the internal clock available to other devices; the instruction decoder interprets the fetched opcode, the 16-bit stack pointer holds the address of the top of the stack, and the 16-bit program counter holds the address of the next instruction byte.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
Descriptive question on the 8085 architecture. Each pin needs its direction, purpose and how software or hardware uses it; each internal unit needs its function in the fetch, decode and execute cycle.
Answer outline
Introduction
The 8085 is an 8-bit NMOS microprocessor introduced by Intel in March 1976. It runs from a single +5 V supply (pin 40, with ground at pin 20) and has an on-chip clock generator.
READY (pin 35, input)
- Lets the 8085 work with slower memories and I/O devices through externally generated wait states
- While a slow device keeps READY inactive, the processor waits instead of completing the bus cycle
- Used to synchronise slow memory or I/O devices with the processor
SID and SOD
- SID: serial input data line, read into the accumulator by the RIM instruction
- SOD: serial output data line, driven from the accumulator by the SIM instruction
- RIM and SIM are the only 8085 instructions not taken from the 8080, and each takes four T-states
- Together they give software-controlled serial communication without an external serial interface chip
INTR (input)
- The externally serviced interrupt request, alongside TRAP and the vectored RST 7.5, 6.5 and 5.5
- Maskable: enabled by EI and disabled by DI
- The external hardware supplies an instruction such as an RST (a one-byte call to 00H, 08H, ..., 38H) to invoke the service routine
CLK (OUT) (output)
- The on-chip clock generator runs at half the crystal frequency, and this internal clock is available on an output pin
- Other devices in the system use it to stay in step with the processor
Instruction decoder
- The fetched opcode is held in the instruction register
- The decoder interprets it, identifies the operation and how many bytes follow, and drives the timing and control unit to generate the required machine cycles and internal control signals
Stack pointer (SP)
- 16-bit register holding the address of the current top of the stack in read/write memory
- The stack grows downward: PUSH decrements SP by 2 and stores the register pair, POP reads it back and increments SP by 2
- Initialised by LXI SP, address
Program counter (PC)
- 16-bit register holding the memory address of the next instruction byte
- Incremented automatically as each instruction byte is fetched
- Loaded with a new address by JMP, CALL, RET and RST instructions
Conclusion
These pins and registers together give the 8085 its interfacing (wait states, serial I/O, interrupts, clock) and its sequencing of program execution.
Examples and data to cite
- The 8085 has five interrupts: TRAP (non-maskable), the maskable vectored RST 7.5, RST 6.5 and RST 5.5, and the externally serviced INTR; all except TRAP are enabled by EI and disabled by DI.
- A 6.14 MHz crystal gives a 3.07 MHz internal clock, half the crystal frequency.
Facts to remember
- READY is pin 35; +5 V supply is pin 40 and ground pin 20.
- SID and SOD carry serial data, received and sent through RIM and SIM.
- The 8085 has a 16-bit program counter and a 16-bit stack pointer.
- PUSH: SP ← SP − 2, so the stack grows downward in memory.
- RST n is a one-byte call to address 8 × n (00H to 38H).