Answer the following questions in about 150 words each :
What are the different resolutions used in remote sensing? Explain their significance.
10 marks · answer in 150 words · directive: Explain
The core of a good answer
A remote sensing system is described by four resolutions, spatial (smallest ground detail, set by pixel size), spectral (number and width of wavelength bands), radiometric (number of brightness levels, in bits) and temporal (revisit interval); together they decide what can be seen, identified, distinguished and monitored, and they trade off against one another.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
The question needs a definition of each of the four resolutions with typical values and Indian or global sensor examples, followed by their significance for geological and other applications, including the trade-offs between them.
Answer outline
Introduction
Resolution is the ability of a sensor to record detail; it has four components that together determine the information content of an image.
Spatial resolution
- Size of the ground area represented by one pixel; typically about 1 m to 1,000 m.
- Examples: Landsat 8 OLI 30 m multispectral and 15 m panchromatic; thermal 100 m; Cartosat-3 panchromatic about 0.25 m; Resourcesat LISS-IV 5.8 m, LISS-III 23.5 m, AWiFS 56 m.
- Significance: fine resolution for detailed mapping of small outcrops, faults, mines and landslides; coarse for regional geology.
Spectral resolution
- Number and width of bands recorded: panchromatic (one broad band), multispectral (a few to about a dozen bands), hyperspectral (hundreds of narrow bands).
- Examples: Landsat OLI 9 bands plus 2 thermal bands; Hyperion on EO-1, 220 bands from 0.4 to 2.5 µm.
- Significance: narrow contiguous bands give a spectrum for each pixel, so many minerals can be identified; the most diagnostic mineral features lie at longer wavelengths (shortwave and thermal infrared).
Radiometric resolution
- Number of distinguishable intensity levels, expressed in bits, typically 8 to 14 bits: 8 bits = 256 levels; 12 bits = 4,096 levels; 14 bits = 16,384 levels.
- Landsat 8 uses 12-bit quantisation.
- Significance: detects subtle tonal differences in shadow, water and similar lithologies.
Temporal resolution
- Frequency of revisits over the same area: Landsat 16 days.
- Significance: change detection, monitoring of floods, landslides, glaciers, volcanic activity and mining; repeat passes are also needed where cloud cover obscured an earlier image.
Trade-offs
- Very narrow bands lower the signal-to-noise ratio, while pixels that are too large mix several objects, so spectral and spatial resolution must be balanced; hyperspectral cubes are large datasets that need significant storage and transmission capacity.
Conclusion
Choice of sensor depends on the problem: the resolution that matters most for lithological mapping is spectral, for structural detail spatial, and for hazard monitoring temporal.
Examples and data to cite
- Landsat 8 launched 11 February 2013: OLI 30 m, panchromatic 15 m, TIRS 100 m, swath 185 km, 12-bit data.
- Cartosat-3 (ISRO, launched 2019): panchromatic resolution about 0.25 m.
- EO-1 Hyperion: 220 bands from 0.4 to 2.5 µm, each about 0.10 to 0.11 µm wide.
- Resourcesat-2: LISS-4 (5.8 m), LISS-3 (23.5 m) and AWiFS (56 m) give three spatial resolutions from one platform.
Facts to remember
- The four resolutions are spatial, spectral, radiometric and temporal.
- Number of grey levels = 2 raised to the number of bits.
- Hyperspectral sensors collect contiguous narrow bands that give a near-continuous spectrum per pixel.