Discuss the types of folds. Add a note on the classification of folds based on the mechanism of folds.
15 marks · directive: Discuss
The core of a good answer
Folds are classified by geometry (anticline and syncline, antiform and synform, attitude of the axial surface, interlimb angle and the layer thickness pattern shown by dip isogons) and by mechanism (buckling with flexural slip, passive or flow folding, and fault-related folding); the mechanism classification explains why concentric folds form by buckling of competent layers while similar folds usually form by shear flow.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
The first part asks for a descriptive classification of folds with sketches; the second asks for a genetic classification by fold mechanism. The answer should give standard terms, the interlimb angle and dip isogon classes, and the mechanisms with their diagnostic features.
Answer outline
Introduction
A fold is a stack of originally planar surfaces, such as sedimentary strata, that are bent or curved during permanent deformation; its parts are the hinge (line of maximum curvature), the limbs (flanks converging at the hinge zone) and the axial surface joining the hinge lines of stacked surfaces.
By direction of closure and age of core
- Antiform: strata dip away from the axial centre; synform: strata dip towards it; used when the age order is unknown or inverted.
- Anticline: oldest strata in the core; syncline: youngest strata in the core, irrespective of orientation.
By attitude of axial plane and hinge
- Recumbent fold: axial plane at a low angle, so the strata of one limb are overturned.
- Dome: strata dip away from the centre in all directions, oldest strata in the centre; basin: strata dip towards the centre, youngest strata in the centre.
- Plunging folds form Vs on a geological map that point in the direction of plunge.
By interlimb angle and shape
- Interlimb angle: gentle 180 to 120 degrees, open 120 to 70 degrees, close 70 to 30 degrees, tight 30 to 0 degrees, isoclinal 10 to 0 degrees with essentially parallel limbs.
- Chevron folds (planar limbs meeting at an angular hinge), box folds and kink bands, typical of sandstone-shale sequences; monocline (strata dipping in one direction between horizontal layers); ptygmatic folds (chaotic, random and disconnected); parasitic folds (short-wavelength folds within a larger fold).
By layer thickness: Ramsay dip isogon classes
- Class 1A: orthogonal thickness smaller at the hinge than on the limbs; Class 1B: parallel folds; Class 1C: orthogonal thickness smaller on the limbs than at the hinge.
- Class 2: dip isogons parallel, similar folds.
- Class 3: dip isogons diverge.
Classification by mechanism
- Buckling: folding of a planar surface and its confining volume under layer-parallel shortening; concentric folds of uniform layer thickness come from buckling.
- Flexural slip: layer-parallel slip between the layers of the folded strata, like bending a phone book.
- Passive (flow) folding: little resistance is offered by the layering; similar folds usually form by shear flow.
- Fault-related folding: fault-bend folds form by displacement along a non-planar fault; fault-propagation folds form when displacement occurs on an existing fault; detachment folds form when a thrust continues to move above a planar detachment without further fault propagation.
Conclusion
The geometric classification describes what a fold looks like, while the mechanism classification explains how it formed, which helps predict fold shape and the location of anticlinal traps.
Examples and data to cite
- Zagros fold and thrust belt: the Simply Folded Zone has many elongate folds and few surface faults, and the Asmari limestone was folded into anticlinal traps for oil.
- Kink bands, box folds and chevron folds in sandstone-shale sequences.
Facts to remember
- Ramsay's dip isogon classes: 1A, 1B, 1C, 2 and 3.
- Concentric (parallel) folds come from buckling; similar folds usually form by shear flow.
- Parasitic folds are short-wavelength folds formed within a larger wavelength fold.
- A competent layer can withstand an applied load without collapsing; an incompetent layer is relatively weak.