A pressurized steel tank is constructed with a helical weld that makes an angle α = 55° with the longitudinal axis (as shown in the figure). The tank has radius r = 0·6 m, wall thickness t = 18 mm, and internal pressure P = 2·8 MPa. Also, the steel has modulus of elasticity E = 200 GPa and Poisson's ratio v = 0·30.
Determine the following quantities for the cylindrical part of the tank :
(I) The circumferential and longitudinal stresses.
(II) The maximum in-plane and out-of-plane shear stresses.
(III) The circumferential and longitudinal strains.
[Figure, described: a cylindrical tank with domed ends, with a helical weld seam running round the shell at angle α to the longitudinal axis.]
10 marks · directive: Determine
The core of a good answer
σ₁ = Pr/t = 93·3 MPa and σ₂ = Pr/2t = 46·7 MPa; the maximum in-plane shear is (σ₁ − σ₂)/2 = 23·3 MPa and the out-of-plane shear σ₁/2 = 46·7 MPa; the strains are ε₁ = 3·97 × 10⁻⁴ and ε₂ = 9·33 × 10⁻⁵.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
Thin-walled cylinder theory (t/r = 0·03, well under one tenth). The circumferential (hoop) and longitudinal stresses come from equilibrium of a cut shell; the in-plane shear uses the two in-plane principal stresses, the out-of-plane shear uses the radial stress (≈ 0) as σ₃; strains come from the biaxial Hooke's law. The weld angle is not needed for these three quantities.
Answer outline
Introduction
Given r = 600 mm, t = 18 mm, P = 2·8 MPa, E = 200 GPa, ν = 0·30. The outer surface is in biaxial stress with σ₃ = 0.
Step 1: Stresses
- σ₁ (hoop) = Pr/t = 2·8 × 600/18 = 93·33 MPa
- σ₂ (longitudinal) = Pr/(2t) = 46·67 MPa
Step 2: Shear stresses
- In-plane: τ_max = (σ₁ − σ₂)/2 = 23·33 MPa (on planes at 45° to the axis)
- Out-of-plane: τ_max = σ₁/2 = 46·67 MPa (with σ₃ = 0)
Step 3: Strains
- ε₁ = (σ₁ − νσ₂)/E = (93·33 − 14·00)/200000 = 3·967 × 10⁻⁴
- ε₂ = (σ₂ − νσ₁)/E = (46·67 − 28·00)/200000 = 9·33 × 10⁻⁵
Step 4: Weld (extra)
- On the weld plane (normal at 35° to the axis): σ = 62·0 MPa and |τ| = 21·9 MPa, by stress transformation; these are needed if the question went on to weld stresses
Conclusion
Hoop 93·3 MPa, longitudinal 46·7 MPa, in-plane shear 23·3 MPa, out-of-plane shear 46·7 MPa, ε₁ = 3·97 × 10⁻⁴, ε₂ = 9·33 × 10⁻⁵. Check: the hoop stress is twice the longitudinal stress, as in every thin cylinder. (Recomputed in Python.)
Examples and data to cite
- The hoop stress is twice the longitudinal stress, so a seam along the axis carries the larger normal stress; the helical weld at 55° sees only 62·0 MPa (Step 4).
Facts to remember
- Thin cylinder: σ_hoop = Pr/t, σ_long = Pr/(2t), valid when the wall thickness is no more than about one tenth of the radius; radial stress is negligible.
- Biaxial Hooke's law: ε₁ = (σ₁ − νσ₂)/E.
- Maximum in-plane shear = (σ₁ − σ₂)/2; absolute maximum shear with σ₃ = 0 is σ₁/2.
- Stress transformation gives normal and shear stress on an inclined weld.