Calculate the pressure at which water will boil at 150 °C, given that the change in specific volume when 1 gram of water is converted into steam is 1676 cm³. Given, latent heat of vaporization for steam = 540 cal per gram, J = 4.2 × 10⁷ ergs/cal and one atmospheric pressure = 10⁶ dynes/cm².
15 marks · directive: Calculate
The core of a good answer
By the Clausius-Clapeyron equation dP/dT = L/[T(V₂ − V₁)] evaluated at the normal boiling point (T = 373 K, where the given volume change applies), dP/dT = 2.268 × 10¹⁰/(373 × 1676) = 3.63 × 10⁴ dyne cm⁻² K⁻¹; a 50 K rise needs ΔP = 1.81 × 10⁶ dyne/cm², so P ≈ 2.81 × 10⁶ dyne/cm² ≈ 2.8 atm.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
Clausius-Clapeyron equation for the liquid vapour boundary. The standard textbook method treats dP/dT as constant over the 50 K interval and evaluates it at 100 °C, where water boils at 1 atm and the given specific volume change applies.
Answer outline
Introduction
Given L = 540 cal/g = 540 × 4.2 × 10⁷ = 2.268 × 10¹⁰ erg/g, V₂ − V₁ = 1676 cm³/g, normal boiling point 100 °C = 373 K at P₀ = 10⁶ dyne/cm², required boiling point 150 °C, ΔT = 50 K.
Step 1: Clausius-Clapeyron equation
- dP/dT = L/[T(V₂ − V₁)]
Step 2: Slope at 100 °C
- dP/dT = 2.268 × 10¹⁰/(373 × 1676)
- dP/dT = 3.628 × 10⁴ dyne cm⁻² K⁻¹
Step 3: Pressure increase
- ΔP ≈ (dP/dT)ΔT = 3.628 × 10⁴ × 50 = 1.814 × 10⁶ dyne/cm²
Step 4: Boiling pressure
- P = P₀ + ΔP = 10⁶ + 1.814 × 10⁶ = 2.81 × 10⁶ dyne/cm² ≈ 2.81 atm
Step 5: Note on the approximation
- If the slope is evaluated at 150 °C (T = 423 K) instead, dP/dT = 3.20 × 10⁴ and P ≈ 2.60 × 10⁶ dyne/cm².
- The linear estimate is rough because L and V₂ − V₁ are taken at their 100 °C values over a 50 K interval.
Conclusion
Water boils at 150 °C under roughly 2.8 × 10⁶ dyne/cm² (about 2.8 atm) on this approximation. Check: units erg g⁻¹/(K cm³ g⁻¹) = dyne cm⁻² K⁻¹.
Facts to remember
- Clausius-Clapeyron: dP/dT = L/[T(V₂ − V₁)].
- Mechanical equivalent of heat J = 4.2 × 10⁷ erg/cal = 4.2 J/cal.
- 1 atm = 10⁶ dyne/cm² (as given in the question).
- Boiling point rises with pressure because V_vapour > V_liquid and L > 0.