The input signal as shown in Figure (I) is applied to the comparator circuit given in Figure (II). Make a sketch of the output signal showing its proper relationship to the input signal. Assume that the maximum output levels of the op-amp are ± 12 V.
[Figure (I), described in words: V_in is a sinusoid plotted against t, starting at 0 at t = 0, rising to a peak of 5 V, returning to 0 and falling to −5 V, for one full cycle.]
[Figure (II), described in words: a voltage divider of R₁ = 8·2 kΩ from + 15 V to a node and R₂ = 1·0 kΩ from that node to ground; the node is connected to the inverting (−) input of the op-amp; V_in is applied to the non-inverting (+) input; the output is V_out.]
10 marks · directive: Sketch
The core of a good answer
The divider fixes the inverting input at V_ref = 15 × 1.0/(8.2 + 1.0) = 1.63 V, so V_out = +12 V while V_in > 1.63 V and −12 V otherwise: for the 5 V sine, V_out is a rectangular pulse at +12 V from ωt = 19.0° to 161.0° of each cycle (39.4% of the period) and −12 V for the rest.
An outline written by upsc.help, not an official UPSC answer; every fact checked by a separate review. How we work
What the question asks
A non-inverting comparator with a positive reference set by a voltage divider. Find the reference, find the phase angles where the sine crosses it, and sketch the output aligned in time with the input.
Answer outline
Introduction
An open-loop op-amp saturates: V_out = +V_sat if V₊ > V₋ and −V_sat if V₊ < V₋. Here V₊ = V_in = 5 sin ωt and V₋ = V_ref.
Step 1: Reference voltage
- V_ref = 15 × R₂/(R₁ + R₂) = 15 × 1.0/9.2 = 1.63 V (no current drawn by the op-amp input)
Step 2: Switching points
- 5 sin θ = 1.63, so sin θ = 0.326
- θ₁ = 19.0°, θ₂ = 180° − 19.0° = 161.0°
Step 3: Output
- 0 ≤ θ < 19.0°: V_in < 1.63 V, V_out = −12 V
- 19.0° < θ < 161.0°: V_in > 1.63 V, V_out = +12 V
- 161.0° < θ ≤ 360°: V_out = −12 V (including the whole negative half cycle)
Step 4: Sketch
- Draw V_in (±5 V sine) with a dashed line at +1.63 V
- Below it draw V_out as a rectangular wave between +12 V and −12 V, rising where the sine crosses 1.63 V going up and falling where it crosses going down
- Positive pulse width = 142.0° of 360°, duty cycle 39.4%
Conclusion
V_out is a ±12 V rectangular wave, high for 39.4% of each cycle (19.0° to 161.0°), centred on the input's positive peak. Check: with a zero reference it would be a 50% square wave; the positive reference narrows the high pulse.
Facts to remember
- Comparator: V_out = +V_sat when V₊ > V₋, −V_sat when V₊ < V₋.
- Voltage divider: V = V_s R₂/(R₁ + R₂).
- Crossing angle θ = sin⁻¹(V_ref/V_p).