2026 · Electrical Engineering Optional Paper II · 10 marksMains
A unity feedback system has open loop transfer function G(s) = K/(s(s + q)). Evaluate the value of K and q so that settling time and peak overshoot will be 6 seconds and 20% respectively.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
Upon execution of the following routine, find the value stored at location 00FFH.
MVI B, 0FH
MVI C, ABH
MOV A, C
ADD B
SBI 02H
STA 00FFH
Also write the status of each flag after completion of execution.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
To evaluate the value of resistance, the voltmeter and ammeter methods are used. The voltmeter reads 500 V with a probable error of ± 20 V and the ammeter reads 15 A with probable error of ± 3 A. Find out the probable error in the computed value of resistance.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
Discuss the saturated-reactor compensator with the help of circuit diagram and V-I characteristics. How can a lower slope of V-I characteristics be obtained ? Also write the main features of the saturated-reactor compensator.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
A discrete memoryless channel has the following channel matrix :
[P(Y|X)] = [1 − p p 0 ; 0 p 1 − p]
(i) Draw the channel diagram.
(ii) If the source has equally likely outputs, compute the probabilities associated with the channel output for p = 0·2.
2026 · Electrical Engineering Optional Paper II · 20 marksMains
Determine the response of the system shown in the following figure when it is excited by a unit step input.
[Figure, described in words: R(s) enters a summing junction (+); the junction output passes through a block s + 1 and then a block 2/s² in cascade to give C(s); C(s) is fed back directly to the summing junction with a negative sign (unity negative feedback).]
2026 · Electrical Engineering Optional Paper II · 10 marksMains
In the 8085 microprocessor, explain the functionality of the following pins, and describe the role of the instruction decoder, stack pointer and program counter.
1. READY
2. SID
3. SOD
4. INTR
5. CLK (OUT)
2026 · Electrical Engineering Optional Paper II · 10 marksMains
The following circuit is given for the measurement of voltage across a 150 kΩ resistor as shown in the figure. Two voltmeters whose sensitivities are 2000 Ω/V and 30,000 Ω/V respectively are used one by one for this purpose. Both voltmeters have a range of 0 – 100 V. Calculate the reading of each voltmeter.
[Figure, described in words: the + terminal of a 200 V d.c. source connects through a 300 kΩ resistor to a node; a 150 kΩ resistor is connected from that node to the − terminal line; a two-way switch at the node connects either voltmeter V1 or voltmeter V2 across the 150 kΩ resistor.]
2026 · Electrical Engineering Optional Paper II · 10 marksMains
A system has a unit response as c(t) = 1 − e^(−0·5t). Evaluate its unit impulse and unit ramp response, assuming zero initial conditions.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
A linear time-invariant system is characterized by the homogeneous state equation.
[ẋ1 ; ẋ2] = [0 1 ; −1 −2] [x1 ; x2]
Evaluate the solution of the homogeneous equation assuming the initial state vector as x(0) = [1 ; 0].
2026 · Electrical Engineering Optional Paper II · 20 marksMains
An electrodynamometer wattmeter is used for power measurement in a 1-ϕ circuit. The load voltage is 200 V and load current is 20 A at power factor of 0·5 lagging. The wattmeter voltage circuit has a resistance of 5000 Ω and inductance of 60 mH.
Compute the percentage error in the wattmeter reading when pressure coil is connected on the load side. Given that the current coil resistance is 0·4 Ω, inductance is negligible and frequency is 50 Hz. Comment on the result.
2026 · Electrical Engineering Optional Paper II · 20 marksMains
Design a PI controller so that a unity feedback system having open loop transfer function G(s)H(s) = 10/((s + 2)(s + 3)) will have the damping ratio of 0·6 and natural frequency of oscillations will be 4 rad/sec. Also determine the characteristic equation of this controller.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
Write an assembly language program for the 8253/8254 (programmable interval timer) to operate in mode 3 and mode 2.
Use counter 0 for which control word register address is 2DH and counter 0 address is 2BH. Input clock is 1 MHz and output frequency is 1 kHz.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
Design a hardware scheme to interface 8255 (programmable peripheral interface) with 8085, and configure its Port ‘A’ and Port ‘C’ as input ports and Port ‘B’ as output port.
Write an assembly language program to take two different numbers from Port ‘A’ and Port ‘C’ and display the summation of these numbers on Port ‘B’ as output.
Assume the port addresses are :
Port A = 00H
Port B = 01H
Port C = 02H
Control word register address : 03H.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
A thermistor has a resistance of 4290 Ω at ice point and 980 Ω at 60°C. The temperature-resistance relationship is given by R_T = pR₀e^(b/T). Evaluate the constants p and b. Also calculate the range of resistance to be measured if the temperature varies from 70°C to 120°C.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
[Circuit: a voltage source V(t) (+ at top) in series with a resistor R, an inductor L and a capacitor C, forming a single loop; the loop current i(t) flows from the source's + terminal through R and L to C.]
2026 · Electrical Engineering Optional Paper II · 10 marksMains
A 1 V signal with a source resistance of Rₛ = 600 Ω is connected to an oscilloscope which has an input impedance of Rᵢ = 1 MΩ in parallel with Cᵢ = 30 pF. The coaxial cable has a capacitance C_cc = 100 pF. Calculate the oscilloscope terminal voltage (Vᵢ) when the signal frequency is 100 Hz. Also determine the frequency at which Vᵢ is 3 dB below Vₛ.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
In a percentage differential protection scheme, the current in the secondary of the current transformer at one end is 3·4 Amp and the current in the secondary of the current transformer at the other end is 3·0 Amp. The number of turns of the operating coil is 400. Determine the number of turns of the restraining coil for the balance condition. Also explain the requirement of biasing.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
A DM system is designed to operate at 3 times the Nyquist rate for a signal with a 3 kHz bandwidth. The quantizing step size is 250 mV.
(i) Determine the maximum amplitude of a 1 kHz input sinusoid for which the delta modulator does not show slope overload.
(ii) Determine the post-filtered output signal-to-quantizing noise ratio for the signal of part (i).
2026 · Electrical Engineering Optional Paper II · 20 marksMains
Determine the efficiency of a 400 km long transmission line delivering 100 MW load at 240 kV, 0·85 lagging p.f. at the receiving end. The series impedance and shunt admittance per kilometre are 0·175 + j0·375 ohm and 5 × 10⁻⁶ mho respectively.
2026 · Electrical Engineering Optional Paper II · 20 marksMains
Consider a discrete memoryless source with alphabet {s₀, s₁, s₂} and statistics {0·7, 0·15, 0·15} for its output.
(i) Apply the Huffman algorithm to this source. Hence, show that the average code-word length of the Huffman code equals 1·3 bits/symbol.
(ii) Let the source be extended to order two. Apply the Huffman algorithm to the resulting extended source and show that the average code-word length of the new code equals 1·1975 bits/symbol.
(iii) Compare the average code-word length calculated in part (ii) with the entropy of the original source.
2026 · Electrical Engineering Optional Paper II · 20 marksMains
A 3-phase line is terminated by a star-connected resistive load of 800 ohm per phase. The line conductors are equilaterally spaced 2·0 m apart and have a diameter of 2 cm. The voltage wave travelling along the line is of 33 kV. Determine the power reflected by the load and the power consumed by the line.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
A discrete memoryless source X has four symbols x₁, x₂, x₃, x₄ with probabilities P(x₁) = 0·4, P(x₂) = 0·3, P(x₃) = 0·2, P(x₄) = 0·1 respectively.
I. Calculate H(x).
II. Find the amount of information contained in the messages x₁, x₂, x₁, x₃ and x₄, x₃, x₃, x₂ and compare with the H(x) obtained in part (I).
2026 · Electrical Engineering Optional Paper II · 10 marksMains
A parity check code has the parity check matrix :
H = [1 0 1 1 0 0; 1 1 0 0 1 0; 0 1 1 0 0 1]
(rows: 1 0 1 1 0 0 / 1 1 0 0 1 0 / 0 1 1 0 0 1)
I. Determine the generator matrix G.
II. Find the code word that begins with 101... .
III. Suppose that the received word is 110110. Decode this received word.
2026 · Electrical Engineering Optional Paper II · 20 marksMains
A hollow cylinder made of insulating material surrounded by a thin metal sheath has inner and outer diameters of 4 cm and 8 cm respectively. The relative permittivity of the cylinder material is 4 and peak voltage gradient in air is 33 kV/cm. Determine the rms value of safe operating voltage of a conductor passing through the centre of the cylinder and having a diameter of 2 cm.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
Show that the channel capacity of an ideal AWGN channel with infinite bandwidth is given by C∞ = (1/ln 2)·(S/η) ≈ 1·44 (S/η) bit/sec.
Given that :
S is the average signal power and η/2 is the power spectral density of white Gaussian noise.
2026 · Electrical Engineering Optional Paper II · 10 marksMains
A binary FSK system transmits binary data at the rate of 2·5 × 10⁶ bits per second. During the course of transmission, white Gaussian noise of zero mean and power spectral density 10⁻²⁰ watts per hertz is added to the signal. In the absence of noise, the amplitude of the received signal is 1 μV across 50 Ω impedance. Determine the average probability of error assuming coherent detection of the binary FSK signal.