Pratidin

UPSC Mains Mechanical Engineering Optional Paper I previous-year questions

24 Mains Mechanical Engineering Optional Paper I questions from 2026 to 2026, with the official answer where UPSC has published one, an explanation or answer outline, and the news stories that connect to each. Every question is checked against the published paper.

2026

  1. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A uniform beam has a mass of 50 kg per metre length. Compute the reactions at the support O. The force loads shown lie in a vertical plane. [Figure, described: the beam is built in (fixed) at O on a vertical wall. It runs horizontally 1·8 m from O to A, where a 3 kN load acts vertically downward, and a further 0·6 m to a bend. From the bend it rises at 30° to the horizontal: B is 0·6 m along the inclined part and C a further 0·6 m beyond B. A 4 kN-m couple acts at B (drawn anticlockwise), and a 1·4 kN force acts at C perpendicular to the inclined part, directed downward and to the right.]

  2. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    The fixed-ended bar ABCD consists of three prismatic segments, as shown in the figure. The end segments have a cross-sectional area A₁ = 840 mm² and length L₁ = 200 mm. The middle segment has a cross-sectional area A₂ = 1260 mm² and length L₂ = 250 mm. Loads P_B and P_C are equal to 25·5 kN and 17·0 kN, respectively. (i) Determine the reactions R_A and R_D at the fixed supports. (ii) Determine the compressive axial force F_BC in the middle segment of the bar. [Figure, described: the bar is horizontal between fixed walls at A (left) and D (right): AB (area A₁, length L₁), BC (area A₂, length L₂), CD (area A₁, length L₁). P_B acts at B along the axis towards the right; P_C acts at C along the axis towards the left.]

  3. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A turbine shaft of diameter d is under a thrust load P and torque T (as shown in the figure). Calculate the largest permissible value of the load P if the allowable normal stress is not to exceed σ_all. Given : d = 60 mm, T = 2 kN.m, σ_all = 220 MPa [Figure, described: a solid circular shaft of diameter d with an axial force P at each end directed into the shaft (compressive thrust) and equal and opposite torques T at the two ends.]

  4. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    What is heat treatment ? What is its purpose ? Explain different heat treatment processes with the help of common microstructural phases of steel on an Iron-Carbon equilibrium diagram.

  5. 2026 · Mechanical Engineering Optional Paper I · 20 marksMains

    A steel tube has a mean diameter of 100 mm and a thickness of 3 mm. Calculate the torque which can be transmitted by the tube with a factor of safety of 2·25, if the criterion of failure is : (i) Maximum shear stress (ii) Maximum strain energy (iii) Maximum shear strain energy The elastic limit of the steel in tension is 225 MN/m² and Poisson's ratio v is 0·3.

  6. 2026 · Mechanical Engineering Optional Paper I · 20 marksMains

    The effective turning moment of a two-wheeler engine crankshaft for every 180° of crank rotation is represented by : T (N-m) = 8000 + 1000 sin 2θ − 2000 cos 2θ where θ is the crank inclination with respect to the inner dead centre. A flywheel of 500 kg mass with radius of gyration of 750 mm is provided on the crank. Assuming external resistance as constant at an engine speed of 300 rpm, determine : (i) The maximum, minimum and mean torques. Also represent them on a T − θ diagram. (ii) The power developed. (iii) Total percentage fluctuation in speed. (iv) If, owing to size constraints, radius of gyration of the flywheel is reduced to 600 mm, will the percentage (%) fluctuation of speed increase ? If yes, then by how much ?

  7. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    The acceleration of a particle along a straight line is defined by a = (2t − 9) m/s², where t is in seconds. At t = 0, s = 1 m and v = 10 m/s. When t = 9 s, determine : (I) The particle's position, (II) The total distance travelled, and (III) The velocity of the particle.

  8. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A pressurized steel tank is constructed with a helical weld that makes an angle α = 55° with the longitudinal axis (as shown in the figure). The tank has radius r = 0·6 m, wall thickness t = 18 mm, and internal pressure P = 2·8 MPa. Also, the steel has modulus of elasticity E = 200 GPa and Poisson's ratio v = 0·30. Determine the following quantities for the cylindrical part of the tank : (I) The circumferential and longitudinal stresses. (II) The maximum in-plane and out-of-plane shear stresses. (III) The circumferential and longitudinal strains. [Figure, described: a cylindrical tank with domed ends, with a helical weld seam running round the shell at angle α to the longitudinal axis.]

  9. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    The surface of an airplane wing is subjected to plane stress with normal stresses σ_x and σ_y and shear stress τ_xy, as shown in the figure. At a counterclockwise angle θ = 32° from the x-axis, the normal stress is 37 MPa tension, and at an angle θ = 48°, it is 12 MPa compression. If the stress σ_x equals 110 MPa tension, what are the stresses σ_y and τ_xy ? [Figure, described: a plane stress element with σ_x = 110 MPa along x, σ_y along y and τ_xy, all drawn in the positive sense.]

  10. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    Determine the damped natural frequency of the system shown in the figure. [Figure, described: a rigid horizontal bar pivoted at O. A spring of stiffness k connects the left end of the bar, at distance a to the left of O, to the fixed ground A below. A dashpot C, attached to the bar at distance b to the right of O, connects it to the fixed support B above. A point mass m is at the right end of the bar, at distance l from O.]

  11. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A glass-epoxy composite consists of full length fibers of E-glass with modulus 72·5 GPa embedded in epoxy matrix with modulus 3·5 GPa. The volume percentage of glass fibers is 35%. Compute : (i) The modulus of elasticity of the composite in longitudinal and transverse directions. (ii) The strain sustained by fibers and matrix, if a stress of 50 MPa is imposed on a cross-sectional area of 250 mm².

  12. 2026 · Mechanical Engineering Optional Paper I · 20 marksMains

    A simple beam is loaded as shown in the figure. Using the double-integration method, determine the following : (i) The equation of the elastic curve (ii) The slope at the end A (iii) The deflection at the midspan [Figure, described: a simply supported beam AB of span L, pinned at A (x = 0) and on a roller at B (x = L), carrying a linearly varying distributed load of intensity W₀ at A decreasing to zero at B; x is measured from A along the beam and y upward.]

  13. 2026 · Mechanical Engineering Optional Paper I · 20 marksMains

    A shaft carries three eccentric masses of 1 kg each at radial distances of 20, 30 and 20 mm with the central plane 50 mm apart. Their angular positions are 120° apart. If the shaft is balanced by adding two masses at a radius of 700 mm and at distances of 100 mm each from the central plane of the middle eccentric, (i) Determine the magnitudes and angular positions of the masses. (ii) If one of the masses is shifted to a radius of 50 mm due to space constraints, determine the change in its magnitude. Will there be any change in the mass and location of the other masses ?

  14. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    Determine the magnitude P of the horizontal force required to initiate motion of the block of mass m₀ for the cases : (A) P is applied to the right, and (B) P is applied to the left. Compute a general solution in each case, and then evaluate your expression for the values θ = 30°, m = m₀ = 3 kg, μ_s = 0·60, and μ_k = 0·50. [Figure, described: a block of mass m₀ rests on a horizontal floor. A uniform bar of mass m is pinned at its upper end B to a vertical wall on the right; its lower end A rests on the top of the block, the bar making angle θ with the horizontal. The coefficient μ_k is marked at the contact A between bar and block, and μ_s at the contact between block and floor. P(A) is drawn on the right face of the block pointing left (pushing the block away from the wall); P(B) is drawn on the left face pointing right (pushing the block towards the wall).]

  15. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A cylindrical workpiece of 60 mm diameter is turned down to 50 mm over a length of 120 mm on a CNC lathe with cutting speed of 120 m/min and feed of 0·3 mm/rev. Find the machining time.

  16. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A firm chooses between two processes (X and Y) to manufacture a component. Process X has a fixed cost of ₹ 9,60,000/year with a variable cost of ₹ 55/unit. Process Y has a fixed cost of ₹ 15,00,000/year with a variable cost of ₹ 38/unit. The selling price is ₹ 110/unit. (i) Calculate the break-even volume for each process independently. (ii) Determine the cross-over point between Process X and Process Y. (iii) If the firm forecasts demand of 35,000 units, compute the profit under each process and recommend a choice. What is the margin of safety (%) under the preferred process.

  17. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A laser beam delivers 5 J of energy in 0·01 sec over an area of 0·5 mm². Calculate the power density of the laser beam.

  18. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A production process is monitored using X̄ and R charts. Fifteen subgroups of size n = 5 were inspected. The grand mean X̄ = 48·6 mm and the mean range R̄ = 4·2 mm. Use the following control chart constants : A₂ = 0·577, D₃ = 0, D₄ = 2·114, where A₂ is for the X̄ chart, D₃ and D₄ are for the R chart (i) Compute the upper and lower control limits for both the X̄ chart and the R chart. (ii) A separate attribute inspection of 20 lots of 200 units each found a total of 184 defective units. Construct a p-chart : compute p̄ , upper control limit (UCL-p) and lower control limit (LCL-p).

  19. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    Discuss the factors affecting surface finish in machining operations, and list the different profile finishing techniques used in modern manufacturing.

  20. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A strip of width 250 mm is reduced from 30 mm to 20 mm thickness in a rolling mill of roll radius 400 mm. Considering coefficient of friction 0·25 and average flow stress 300 MPa, find the following : (i) Contact length (ii) Rolling force (iii) Check if the biting condition is satisfied

  21. 2026 · Mechanical Engineering Optional Paper I · 20 marksMains

    A biomedical implant requires excellent surface integrity with no thermal damage. From the perspective of non-conventional machining, discuss the following : (i) Suitability of USM, LBM, EDM for biomedical implant machining (ii) Surface defects in each process (iii) Best process selection with justification (iv) Post-processing requirements of the selected process

  22. 2026 · Mechanical Engineering Optional Paper I · 15 marksMains

    In an organization, what do you understand by the roles of flexibility, lean practices and agility ? Explain how flexibility, lean practices and agility are complementary approaches.

  23. 2026 · Mechanical Engineering Optional Paper I · 10 marksMains

    A shaft of nominal size 60 mm is to be fitted into a hole. The tolerances are : Hole tolerance – 0·030 mm Shaft tolerance – 0·020 mm Minimum clearance required – 0·010 mm Determine the following : (i) Maximum clearance (ii) Hole and shaft limits (iii) Allowance

  24. 2026 · Mechanical Engineering Optional Paper I · 20 marksMains

    A spare parts store faces stochastic demand. Annual demand is normally distributed with mean (μ) = 2400 units and standard deviation σ_-D = 300 units. Lead time is fixed at 2 weeks. Assume 50 working weeks/year. Ordering cost = ₹ 800/order, Holding cost = ₹ 18/unit/year, Unit cost = ₹ 240, and Stockout cost = ₹ 90/unit short. The store operates with a continuous review policy. (i) Compute the Economic Order Quantity. (ii) Determine the demand during lead time (mean and standard deviation). (iii) If the desired service level is 95% (z = 1·645), calculate the safety stock and reorder point. (iv) Compute the total annual inventory cost (ordering + holding + safety stock holding). By how much does safety stock inflate total holding cost compared to the zero safety stock scenario ?