2026 · Electrical Engineering Optional Paper I · 10 marksMains
For the circuit shown below, if the power loss in 1 Ω resistor is 16 W, find the value of k in the dependent source using nodal method :
[Figure, described in words: a 10 A current source on the left, arrow pointing up, drives current into the top-left node V_A. A 2 Ω resistor connects V_A to the bottom (reference) line, with current i₀ marked flowing down through it. From V_A, a 1 Ω resistor in series with a dependent voltage source k·i₀ (minus terminal on the left, plus terminal on the right) runs along the top to node V_B. A 5 Ω resistor connects V_B to the reference line, and a 20 V voltage source (plus terminal at the top) is connected between V_B and the reference line on the right.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
Consider the continuous-time system shown in the figure above, which is characterized by the following input-output relationships :
[Figure, described in words: x(t) enters System 1, whose output w(t) enters System 2, whose output is y(t); the two blocks in cascade form the Overall system.]
System 1 : w(t) = ∫ from t−3 to t of x(T) dT
System 2 : y(t) = ∫ from t−6 to t of w(T) dT
(i) Determine whether the overall system is linear and time-invariant.
(ii) Determine and plot impulse response of the overall system.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
Two line currents of infinite extent in the z-direction are at distance d apart along the y-axis. The current I₁ is located at y = d/2 and the current I₂ is located at y = −d/2 as shown in the figure. Find the magnetic field at any point in the y = 0 plane, when the currents are equal, i.e., I₁ = I₂ = I :
[Figure, described in words: x-axis horizontal and y-axis vertical; I₁ is a point on the positive y-axis and I₂ a point on the negative y-axis, the two separated by d and symmetric about the origin.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
A combinational logic circuit consisting of two numbers of 2 to 4 decoders is shown in the figure below :
[Figure, described in words: X drives input A₁ and Y drives input B₁ of the first 2 to 4 decoder, whose outputs are D₀, D₁, D₂, D₃. D₁ and D₂ end in unconnected terminals. D₀ is connected to the upper input of an XOR gate and also to the upper input of an XNOR gate. D₃ is connected to the lower input of the XNOR gate and also to the lower input of the XOR gate. The XOR output drives A₂ and the XNOR output drives B₂ of the second 2 to 4 decoder, whose outputs are Y₀, Y₁, Y₂, Y₃.]
In this circuit, (A₁, B₁) are the inputs and (D₀ to D₃) are the outputs of the first decoder, while (A₂, B₂) are the inputs and (Y₀ to Y₃) are the outputs of the second decoder. Determine the logic expressions for Y₁ and Y₂ in terms of X and Y.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
A 1250 r.p.m., 220 V, 4·5 kW, DC shunt machine is running as a generator delivering rated load at rated speed and voltage. The machine has rated core loss of 250 W, rated armature copper loss of 200 W and field copper loss of 50 W. Now, the prime mover speed is increased by 20% and simultaneously an external resistance is added in the field circuit so that the developed voltage in armature remains the same and load remains unchanged. Find the—
(i) value of the added resistance;
(ii) loss in external resistance and field;
(iii) input power to the generator;
(iv) armature developed voltage.
Neglect friction and windage losses. Assume constant core loss and linear magnetic circuit.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
Find the values of R and C in the figure shown below, so that V_b = 3V_a, also V̄_b and V̄_a are in quadrature. Find also the phase relation between V and V_b, and V_a and I :
[Figure, described in words: a series circuit across V = 240 V, 50 Hz consisting of a 6 Ω resistor and a 0·0255 H inductor (the voltage across these two together is V_b), followed by a resistor R and a capacitor C (the voltage across R and C together is V_a). The current I flows through all four elements.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
For the circuit shown below, find the value of R, if the power supplied by both the sources is equal :
[Figure, described in words: a 100 V voltage source (plus terminal at the top) on the left; its top terminal connects through a 5 Ω resistor to node 1. A 10 Ω resistor connects node 1 to the bottom (reference) line. A 20 Ω resistor connects node 1 to node 2. The resistor R connects node 2 to the reference line, and a 10 A current source on the right, arrow pointing up, drives current into node 2 from the reference line.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
A continuous-time signal x(t), shown in the figure below, has a Fourier transform X(ω). Without explicitly determining X(ω), compute the following quantities :
1. The value of X(0)
2. The value of the integral ∫ from −∞ to ∞ of X(ω) dω
3. The value of the integral ∫ from −∞ to ∞ of |X(ω)|² dω
4. The phase angle of X(ω)
[Figure, described in words: x(t) is a triangle; it is 0 for t ≤ −1, rises linearly from 0 at t = −1 to 2 at t = 1 (passing through 1 at t = 0), falls linearly to 0 at t = 3, and is 0 for t ≥ 3.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
Determine the Z-transform and the corresponding region of convergence (ROC) for the discrete-time sequence x(n) = |n| (1/2)^|n| .
2026 · Electrical Engineering Optional Paper I · 10 marksMains
A uniform plane wave in air is normally incident onto a lossless dielectric plate of thickness λ/8 and intrinsic impedance η = 260 Ω. Determine the standing wave ratio in front of the plate.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
For the circuit shown below, steady state is achieved with switch K open. At t = 0, switch K is closed. Find the time expression of current in R_L. Also find its initial and final values :
[Figure, described in words: a 50 V source (plus terminal at the top) on the left; its top terminal connects through a 5 Ω resistor to node A. From node A a branch of a 20 Ω resistor in series with a 1 H inductor goes down to the bottom (return) line. From node A the switch K (closing at t = 0) connects to a load resistor R_L = 20 Ω, whose other end is on the bottom line.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
Find the y-parameters of the two-port network shown below :
[Figure, described in words: port 1 (terminals 1 and 1′, voltage V₁, current I₁ entering terminal 1) and port 2 (terminals 2 and 2′, voltage V₂, current I₂ entering terminal 2) share a common bottom line 1′ to 2′. A 1 Ω resistor is connected from terminal 1 to the bottom line. A 2 Ω series resistor connects terminal 1 to the node at terminal 2. At the terminal 2 node, a 2 Ω resistor goes to the bottom line and a dependent current source of value 3I₁ also goes to the bottom line, its arrow pointing down (current 3I₁ flowing from the terminal 2 node to the bottom line).]
2026 · Electrical Engineering Optional Paper I · 20 marksMains
For the following circuit given in Fig. (1) below, the diode has the I-V characteristic in forward direction as shown in Fig. (2) :
[Fig. (1), described in words: a diamond (bridge) of four resistors with top node T, bottom node B, left node L and right node R: 2·0 Ω between L and T, 6·0 Ω between T and R, 8·0 Ω between L and B, and 8·0 Ω between B and R. A diode is connected from T to B, anode at T and cathode at B, with the current i_d marked flowing downwards. A 20 V battery is connected between L and R below the bridge (as drawn, its longer plate, the positive terminal, is on the side connected to L).]
[Fig. (2), described in words: forward characteristic i_d against v_d; i_d = 0 up to v_d = 0·7 V, then a straight line rising to i_d = 1·0 A at v_d = 0·9 V.]
Find the (i) diode current, (ii) diode power loss and (iii) power supplied by the source.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
The outer diameter of the inner conductor and the inner diameter of the outer conductor of a coaxial copper transmission line are 2 mm and 7 mm, respectively. Both the conductors have thickness much greater than the skin depth. The dielectric is lossless and the operating frequency is 400 MHz. Calculate the resistance per meter length of the transmission line. The resistivity and relative permeability of the copper are approximately ρ = 1·724 × 10⁻⁸ Ω-m and 1, respectively.
2026 · Electrical Engineering Optional Paper I · 15 marksMains
The continuous-time signal x(t) = cos(20πt + π/4) is ideally sampled at a rate of 30 samples per second. The resulting sampled signal is then passed through a filter whose impulse response is h(t) = [sin(πt)/(πt)] · cos(80πt − π/2). Find the expression for the output signal of the filter.
2026 · Electrical Engineering Optional Paper I · 5 marksMains
A discrete-time sequence x(n) = {3, 5, 1, 4, −3, 5, −2, −2, 4} of length 9 has a 9-point DFT denoted by X(k), where k = 0, 1, 2, ..., 8. Another discrete-time sequence y(n) has a 9-point DFT given by
Y(k) = e^{j4πk/3} X(k), k = 0, 1, 2, ..., 8
Without explicitly computing DFT or inverse DFT, determine the sequence y(n).
2026 · Electrical Engineering Optional Paper I · 10 marksMains
For the circuit shown in the figure below, the two transistors Q₁ and Q₂ have β₁ = 35 and β₂ = 30. The resistance R₂ is variable. The output voltage V_o across resistance R_o is +5·0 V. If the voltage V_CC is kept at +12·0 V, find the value of R₂. Derive any formula used. Assume V_BE = 0·7 V for both the transistors :
[Figure, described in words: R₁ = 100K is connected from V_CC = +12·0 V to the base of Q₁, and the variable resistor R₂ from the base of Q₁ to ground, forming a divider. The collectors of Q₁ and Q₂ are both connected to V_CC. The emitter of Q₁ drives the base of Q₂ (Darlington connection). The emitter of Q₂ is connected through R_o = 1 kΩ to ground, and V_o = +5·0 V is taken at the emitter of Q₂.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
A single-phase, full-wave bridge diode rectifier supplied from 240 V, 50 Hz AC source is feeding a resistive load R_L = 100 Ω as shown in the figure below. Due to fault in the diode D₂, it behaves like a resistance of 1 kΩ. Sketch the load voltage, load current and source current waveforms under faulty condition. Also calculate the load average voltage and r.m.s. source current under this situation :
[Figure, described in words: a bridge with a left leg and a right leg between a top rail and a bottom rail. Left leg: D₁ from the left midpoint (anode) to the top rail (cathode), and D₄ from the bottom rail (anode) to the left midpoint (cathode). Right leg: D₃ from the right midpoint (anode) to the top rail (cathode), and D₂ from the bottom rail (anode) to the right midpoint (cathode). One source terminal goes to the left midpoint and the other to the right midpoint. R_L = 100 Ω is connected between the top rail and the bottom rail.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
For the circuit given in the figure below, the input voltage signal is given by Vᵢₙ = 1·5 sin 62·8t + 0·5 sin 188·4t volts. Determine the output voltage expression for each input component indicating their magnitude and phases. Derive the frequency domain expression for the output voltage :
[Figure, described in words: Vᵢₙ is applied through a series capacitor C = 1·0 μF to the non-inverting (+) input of an op-amp; R₁ = 10K connects the + input to ground. The output Vₒ is fed back to the inverting (−) input through R₃ = 10K, and R₂ = 22K connects the inverting input to ground.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
A 110/220 V, 1·5 kVA, 50 Hz, single-phase transformer absorbs 150 W power when supplied from a 10 V DC source to its LV side with HV side shorted. It absorbs 10 W at 0·4 p.f. lag when the source voltage is changed to 10 V, 50 Hz AC at the LV side and HV side shorted. It takes 50 W power at 0·2 p.f. lag with rated voltage at LV side and HV side open. Now, if the transformer is to be used at 60 Hz frequency at rated voltage and kVA, then find (i) the maximum efficiency at unity power factor load and (ii) the no-load current, input power and power factor at the LV side with rated voltage.
Neglect skin effect and stray losses. Assume linear magnetic circuit, core loss without hysteresis component and same R/X ratio at both LV and HV side.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
The thyristor T in the circuit shown below is turned on at t = 0, when key K is switched off. Determine the conduction time of T and the capacitor voltage after T is turned off. Given that the inductor carries an initial current of 250 A and initial capacitor voltage is zero :
[Figure, described in words: A 250 A current source (arrow pointing towards the V_s end of L) in series with key K (marked open at t = 0) is connected across the inductor L = 10 μH, so that before t = 0 it circulates 250 A through L in the direction from V_s towards T. V_s = 200 V (positive terminal at the inductor end), L, thyristor T and C = 10 μF (voltage V_C, positive at the T end) form a single series loop.]
2026 · Electrical Engineering Optional Paper I · 10 marksMains
A discrete random variable has two possible values X = 1 or X = 0 with probabilities p and 1 − p, respectively. The probability density function of X is shown in the figure :
[Figure, described in words: two impulses on the x axis, of strength 1 − p at x = 0 and of strength p at x = 1.]
If Y = Σᵢ₌₁ⁿ Xᵢ, where Xᵢ, i = 1, 2, ..., n are statistically independent and identically distributed random variables, what is the probability distribution function of Y?
2026 · Electrical Engineering Optional Paper I · 10 marksMains
A circuit consists of a resistor, a variable inductor and a capacitor, all in series. When the circuit is connected across a 300 V, 50 Hz supply, the maximum current is recorded as 0·3 A by varying the inductor. The voltage across the capacitor is then recorded as 900 V. Determine the resistance, inductance and capacitance of the circuit.
2026 · Electrical Engineering Optional Paper I · 20 marksMains
Design a MOD-6 synchronous DOWN counter using J-K flip-flops.
2026 · Electrical Engineering Optional Paper I · 20 marksMains
A three-phase, star-connected, 415 V, 50 Hz, cage-type induction motor takes a starting current equal to 10 times of its no-load current magnitude. The starting torque is one-third (1/3 times) of its pull-out torque (POT), all under rated conditions. The motor takes 300 W input power at 0·2 p.f. lag with rated supply voltage and frequency. Its core loss has no hysteresis component. Find the starting current and input p.f. of the motor at 5 Hz supply voltage maintaining rated V/f ratio. Neglect stator leakage impedance and rotor current at no load. Assume linear magnetic circuit.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
A three-stage cascade amplifier given below receives a noise power of 1 × 10⁻¹⁶ W. What will be the output noise power?
[Figure, described in words: P_ni enters amplifier 1 (F₁ = 10, G₁ = 20), whose output feeds amplifier 2 (F₂ = 20, G₂ = 40), whose output feeds amplifier 3 (F₃ = 30, G₃ = 50), giving P_no.]
where Fᵢ and Gᵢ are the noise figure and gain of the iᵗʰ amplifier.
2026 · Electrical Engineering Optional Paper I · 20 marksMains
Design a Programmable Logic Array (PLA) for a combinational logic circuit that computes the square of 3-bit binary numbers. Determine the minimum number of product terms required and construct the corresponding PLA programming table for the implementation.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
(i) A single-phase, one-pulse, SCR-controlled converter with R-L-E load has the following data :
Supply voltage V_s = 230 V at 50 Hz, R = 2 Ω, L = 1 mH, E = 120 V, firing angle α = 25° and extinction angle β = 220°
1. Calculate the voltage across the SCR at the instant SCR is triggered.
2. Find the voltage that appears across the SCR when current decays to zero.
3. Find the peak inverse voltage for the SCR.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
(ii) For a type-A chopper feeding an R-L-E load, show that the maximum value of average current rating for the freewheeling diode, in case the load current remains continuous, is given by
I_fd max = [(V_s/4R)(1 − E/V_s)²]
where V_s is the input voltage to the chopper.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
The signal m(t) shown in the following figure is used once to frequency modulate a carrier and once to phase modulate the same carrier :
[Figure, described in words: m(t) rises linearly from 0 at t = 0 to 1 at t = 1, stays at 1 from t = 1 to t = 2, is −1 from t = 2 to t = 3, and is zero elsewhere.]
Find the relation between k_p and k_f such that the maximum phase of the modulated signal in both the cases is equal, where k_p and k_f are phase and frequency sensitivities, respectively of the modulator.
2026 · Electrical Engineering Optional Paper I · 20 marksMains
A 6·6 kV, three-phase, star-connected, cylindrical rotor alternator develops rated voltage with field current of 5 A on open circuit. It takes 100 A armature current at 0·2 p.f. lag for 1·0 A field current with its armature symmetrically shorted, all at rated speed. The alternator is delivering maximum power at rated speed to 6·6 kV bus with a field current of 4·5 A.
Find the (i) power generated and delivered by the alternator, (ii) load angle and (iii) power factor and reactive power of the alternator.
Assume linear magnetic circuit.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
(i) A 240 V, 1200 r.p.m., 15 A, separately excited DC motor has armature resistance of 1·0 Ω. The motor is operated under dynamic braking with chopper control. The braking resistance has a value of 20 Ω.
1. Calculate the duty ratio of the chopper for the motor speed of 1000 r.p.m. and braking torque equal to 1·5 times the rated motor torque.
2. What will be the motor speed for the duty ratio of 0·5 and motor torque equal to its rated torque?
2026 · Electrical Engineering Optional Paper I · 10 marksMains
(ii) A 200 V, 875 r.p.m., 150 A, separately excited DC motor has an armature resistance of 0·06 Ω. It is fed from a single-phase fully controlled rectifier with an AC source voltage of 230 V, 50 Hz. Assuming the continuous conduction, calculate the—
1. firing angle (α) for rated motor torque and 750 r.p.m.;
2. firing angle for rated motor torque and (−500) r.p.m.;
3. motor speed for α = 160° and rated torque.
2026 · Electrical Engineering Optional Paper I · 10 marksMains
An FM signal with a frequency deviation of 15 kHz at a modulation frequency of 5 kHz is applied to two frequency multipliers connected in cascade. The first multiplier multiplies the frequency by 1·5 times and the second multiplier multiplies it by 4 times. Determine the frequency deviation and the modulation index of the FM signal obtained at second multiplier output. Also compute the approximate bandwidth of the FM signal.