Pratidin

UPSC Mains Mechanical Engineering Optional Paper II previous-year questions

30 Mains Mechanical Engineering Optional Paper II questions from 2026 to 2026, with the official answer where UPSC has published one, an explanation or answer outline, and the news stories that connect to each. Every question is checked against the published paper.

2026

  1. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    A piston-cylinder contains 2 kg of argon at T₁ = 300 K and V₁ = 1 m³ (state 1). Argon is heated by an electric heater of 10 A, 220 volts for 10 seconds at constant volume; during the process, 20% heat is lost (state 2). The gas is now allowed to expand from pressure P₂ to a final state with temperature T₃ = 40 °C and final pressure P₃ = 0.5P₂ (state 3). The process 2–3 follows PVⁿ = constant. Find the index of expansion n for the process 2–3. Take for argon R = 0.2081 kJ/kg-K and Cᵥ = 0.312 kJ/kg-K.

  2. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    A gas turbine plant operates on ideal Brayton cycle between T_min = 300 K and T_max = 1200 K. Find the maximum work done per kg of air and the corresponding cycle efficiency. Assume Cₚ of air as 1.005 kJ/kg-K.

  3. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    An air jet (γ = 1.4, R = 287 J/kg-K) at 425 K has sonic velocity. Determine the (i) velocity of sound at the stagnation condition, (ii) maximum velocity of the jet and (iii) Crocco number.

  4. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    Determine the heat transfer through the composite wall shown in the figure below. Take the thermal conductivities of A, B, C, D and E as 50, 10, 8, 20 and 25 W/m-K, respectively and assume one-dimensional heat transfer : [Figure, described in words: a composite wall drawn in perspective, with T₁ = 800 °C and an arrow Q entering the left face and T₂ = 200 °C on the right face, which is labelled A = 1 m². From left to right the layers are: A, 5 cm thick, over the full height; then B above C, side by side in the same 10 cm thick layer, separated by a horizontal line drawn at mid-height (the areas of B and C are not marked); then D, 10 cm thick, over the full height; then E, 5 cm thick, over the full height.]

  5. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    Consider a large plane wall of thickness 0.25 m, having thermal conductivity 3 W/m-°C and surface area 10 m². The left side of the wall is subjected to a net heat flux of 750 W/m². The surface temperature of the left side of the wall is 90 °C. Assuming constant thermal conductivity and no heat generation in the wall, express the differential equation and boundary conditions for steady one-dimensional heat conduction through the wall. Also, obtain a relation for the variation of temperature in the wall by solving the differential equation and find the temperature of the right side of the wall.

  6. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    During a heat transfer process, the entropy change of incompressible substances, such as water, can be determined from ΔS = mC_avg ln(T₂/T₁). Show that for thermal energy reservoirs, such as large lakes, this relation reduces to ΔS = Q/T.

  7. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    A refrigeration system is to cool bread loaves with an average mass of 400 g from 25 °C to −10 °C at a rate of 400 loaves per hour by refrigerated air at −25 °C. Taking the average specific and latent heats of bread to be 2.90 kJ/kg-°C and 109.15 kJ/kg, respectively, determine (1) the rate of heat removal from the bread in kJ/hr and (2) the required volume flow rate of air in m³/hr, if the temperature rise of air is not to exceed 5 °C. The gas constant of air is 0.287 kPa-m³/kg-K. The specific heat of air at average temperature is 1.0 kJ/kg-°C. Take atmospheric air pressure as 101.3 kPa.

  8. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    Show that the entropy change across the normal shock in an adiabatic flow in a duct is given by ΔS = −R ln(P₀Y/P₀X).

  9. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    Differentiate between Fanno and Rayleigh flows.

  10. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    Wind is blowing at 50 km/hr along a 12 m long and 5 m high wall of a house. The atmospheric air is at 4 °C and the wall surface temperature is 10 °C. Determine the rate of heat loss from the wall by convection. The properties of air at 1 atmosphere and at mean film temperature may be taken as : k = 0.0248 W/m-°C ν = 1.412 × 10⁻⁵ m²/s Pr = 0.72 Use the Nusselt number correlation for combined flow : Nu = (0.037 Re⁰·⁸ − 871) Pr⁰·³³

  11. 2026 · Mechanical Engineering Optional Paper II · 20 marksMains

    Steam at 40 °C is condensed in a power plant using cooling water available at 12 °C. The flow rate of steam is 0.15 kg/s. The cooling water is circulated through a bank of 6 m long and 1.25 cm internal diameter thin copper tubes at a mean velocity of 3.5 m/s, and leaves at a temperature of 20 °C. The tubes are nearly isothermal at 40 °C. Calculate the average heat transfer coefficient between the water and the tubes, and find the number of tubes needed to achieve the indicated heat transfer rate in the condenser. The properties of water at an average temperature may be taken as : ρ = 998.8 kg/m³ Cₚ = 4184.5 J/kg-°C h_fg (water) = 2406 kJ/kg

  12. 2026 · Mechanical Engineering Optional Paper II · 20 marksMains

    The mean diameter of the rotor of an axial flow compressor is 0.5 m, and it rotates at 15000 r.p.m. The flow velocity is 220 m/s and is constant. The velocity of whirl at the inlet is 80 m/s. The inlet pressure and temperature are 1 bar and 300 K, respectively. The stage efficiency is 0.88. The pressure ratio through the stage is 1.5. Draw the velocity triangles and determine the (i) blade angles at inlet and outlet, (ii) power input and (iii) degree of reaction. Take ratio of specific heats for air = 1.4 and Cₚ = 1.005 kJ/kg-K.

  13. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    Thin square plates of size 2.5 m × 2.5 m are coming out of an oven at 280 °C in a material processing facility. The plates are cooled by blowing ambient air at 20 °C horizontally parallel to their surfaces. Determine the air velocity above which the natural convection effects on heat transfer are less than 12% and thus are negligible. The kinematic viscosity of air at 1 atmosphere may be taken as ν = 2.859 × 10⁻⁵ m²/s.

  14. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    What does the NTU of a heat exchanger represent? Is a heat exchanger with a very large NTU necessarily a good one?

  15. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    Consider an oil-to-oil double-pipe heat exchanger, whose flow arrangement is not known. The temperature measurements indicate that the cold oil enters at 18 °C and leaves at 50 °C, while the hot oil enters at 75 °C and leaves at 40 °C. Assuming the mass flow rates of both the oils to be identical, determine the effectiveness and flow configuration of this heat exchanger.

  16. 2026 · Mechanical Engineering Optional Paper II · 20 marksMains

    A horizontal insulated cylinder has a frictionless and adiabatic piston held against stops by an external force of 500 kN, as shown in the figure below. The cross-sectional area of the piston is 0.5 m², and the initial volume is 0.25 m³. Helium gas in the cylinder is at 200 kPa, 100 °C. A valve is now opened to a line through which helium is flowing at 1.2 MPa, 200 °C, and the helium flows in, until the cylinder pressure just balances the external force on the piston, at which point the valve is closed. Assume ambient at T₀ = 300 K; for helium, Cₚ = 5.193 kJ/kg-K, R = 2.0771 kJ/kg-K and Cᵥ = 3.116 kJ/kg-K : [Figure, described in words: a vertical supply line on the left is joined through a valve to the left end wall of a horizontal cylinder containing helium; at the right end the piston rests against stops on the helium side, and the external force F_ext pushes it from the right, towards the helium.] Determine : (i) The final mass in the cylinder (in kg) (ii) The final temperature in the cylinder (in K) (iii) The total entropy generation (in kJ/K) (iv) The irreversibility (in kJ)

  17. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    Consider two black surfaces A₁ and A₂ as shown in the figure below. Define the term ‘radiation shape factors’. Also, find a general expression for the energy exchange between these surfaces when they are maintained at different temperatures T₁ and T₂, respectively. If both the surfaces are at the same temperature, find out the reciprocity relationship between them : [Figure, described in words: two black plane surfaces drawn as tilted rectangles, A₁ at temperature T₁ (lower left) and A₂ at temperature T₂ (upper right); on each a pair of crossing lines marks a point, and the two points are joined by a straight line of length r.]

  18. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    The air-fuel ratio of an SI engine varies under different operating conditions. Write the air-fuel ratio requirement for an engine under the following conditions with reasons : (i) Idling or no-load condition (ii) Cruising or part-load condition (iii) Maximum power or full-load condition

  19. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    What are the functions of lubricant used in IC engines? Mention the essential properties of IC engine lubricant.

  20. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    Describe the behaviour of steam flow in a convergent nozzle when it is operated at— (i) design pressure ratio; (ii) pressure ratio higher than the design value; (iii) pressure ratio lower than the design value.

  21. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    List the deviations that occur in a compression process in actual vapour compression refrigeration cycle in comparison to simple saturated vapour compression refrigeration cycle. Also, specify the reasons for these deviations.

  22. 2026 · Mechanical Engineering Optional Paper II · 20 marksMains

    In an Otto cycle, the pressure and temperature at the beginning of compression are 1 bar and 47 °C, respectively. Calculate the theoretical thermal efficiency of this cycle, if the pressure at the end of the compression is 15 bar. The peak temperature during the cycle is 2100 K. Calculate— (i) the heat supplied per kg of air; (ii) the work done per kg of air; (iii) the pressure at the end of expansion. Take Cᵥ = 0.717 kJ/kg-K and γ = 1.4.

  23. 2026 · Mechanical Engineering Optional Paper II · 20 marksMains

    A single-row impulse steam turbine with a blade speed of 200 m/s and mass flow rate of 4 kg/s develops 300 kW of power. Steam leaves the nozzle at 500 m/s and the blade velocity coefficient is 0.92. If the steam leaves the turbine at such an angle that the exit absolute velocity is kept minimum, determine all the angles and diagram efficiency. Draw compound velocity triangles.

  24. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    “The COP of a simple vapour absorption refrigeration system is lower than the COP of a simple vapour compression refrigeration system under identical temperature conditions.” Is this statement correct thermodynamically? Justify your answer.

  25. 2026 · Mechanical Engineering Optional Paper II · 20 marksMains

    In a cogeneration plant, the net power output is 6 MW and the heating load is 1.5 MW. Steam is generated at 40 bar and 500 °C, and is expanded isentropically through a turbine to a condenser at 0.1 bar. The heating load is supplied by extracting steam from the turbine at 2 bar, which is condensed in a process heater to saturated liquid at 2 bar and then pumped back to the boiler. Draw the schematic and T-s diagram. Determine (i) the steam generation capacity (in kg/s) of the boiler and (ii) mass flow rate (in kg/s) of the steam through the heating load. The steam properties at 40 bar, 500 °C are h = 3445.21 kJ/kg, s = 7.09 kJ/kg-K. Use steam tables given at the end to get other properties.

  26. 2026 · Mechanical Engineering Optional Paper II · 20 marksMains

    An R717 simple saturation cycle refrigerator operates at 40 °C condenser and −16 °C evaporator temperatures. Determine COP and power per TR. If a liquid-vapour regenerative heat exchanger is installed in the system, with the suction vapour at 15 °C, what will be the effect on COP and power per TR? Assume specific heat of vapour at condenser temperature as 3.1 kJ/kg-K, when no heat exchanger is used, and 2.9 kJ/kg-K, when heat exchanger is used. The properties of R717 are given in the table below : Temperature (°C) | Enthalpy (kJ/kg): Liquid (h_f), Vapour (h_g) | Entropy (kJ/kg-K): Liquid (s_f), Vapour (s_g) −16 | 126.73, 1442.60 | 0.72511, 5.8420 40 | 390.59, 1490.42 | 1.64377, 5.1558 Draw the P-h diagram also. The specific heat of vapour corresponding to evaporator temperature may be assumed as 2.38 kJ/kg-K.

  27. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    How are the ratings of SI and CI engine fuels done? Explain in brief.

  28. 2026 · Mechanical Engineering Optional Paper II · 20 marksMains

    An air-conditioned space is maintained at 25 °C DBT and 50% RH. The outside conditions are 40 °C DBT and 27 °C WBT. The space has a sensible heat gain of 24.5 kW. Conditioned air is supplied to the space as saturated air at 10 °C. The equipment consists of an air washer. The air entering the air washer comprises 25% of outside air, the remainder being recirculated room air. Calculate the— (i) volume flow rate of air supplied to space; (ii) room sensible heat factor; (iii) cooling load (in TR) of air washer. Psychrometric chart is given at the end. Also, draw the schematic diagram and show the various processes on a skeleton psychrometric chart.

  29. 2026 · Mechanical Engineering Optional Paper II · 15 marksMains

    The following details are noted in a test on a four-cylinder, four-stroke engine : Diameter = 100 mm Stroke = 125 mm Speed of the engine = 1500 r.p.m. Fuel consumption = 0.2 kg/min Calorific value of fuel = 44000 kJ/kg Difference in tension on either side of the brake pulley = 450 N Brake drum circumference = 300 cm If the mechanical efficiency is 80%, calculate the— (1) brake thermal efficiency; (2) indicated thermal efficiency; (3) indicated mean effective pressure; (4) brake-specific fuel consumption.

  30. 2026 · Mechanical Engineering Optional Paper II · 10 marksMains

    A chimney of 35 m height is discharging the flue gases at 300 °C, when the ambient temperature is 25 °C. The quantity of air supplied is 16 kg per kg of fuel burnt. Determine the— (i) draught produced in mm of water; (ii) equivalent draught in metres of hot gas column; (iii) efficiency of the chimney, if the minimum temperature of artificial draught is 120 °C and the mean specific heat of hot flue gases is 1.005 kJ/kg-K; (iv) percentage of heat spent in natural draught system, if the net calorific value of the fuel is 33000 kJ/kg.