2026 · Civil Engineering Optional Paper I · 10 marksMains
A frictionless pulley A as shown in the figure is supported by two bars AB and AC which are hinged at B and C to a vertical wall. A flexible cable, hinged at D, goes over the pulley and supports a load 30 kN at the other end E. The angles between the members are shown in the figure. Neglecting the size of the pulley, determine the forces in the bars AB and AC by drawing the free body diagram :
[Figure, described in words: B, D and C lie on the vertical wall in that order from top to bottom, with A to the right of the wall. Bar AB makes 60° with the wall at B; the cable portion DA makes 60° with the wall at D; bar AC makes 30° with the wall at C; the angle at A between DA and AC is 30°. The cable leaves the pulley at A vertically downwards to the 30 kN load at E.]
2026 · Civil Engineering Optional Paper I · 10 marksMains
Draw the bending moment diagram and shear force diagram for the beam ABCD. The beam supports a point load of 12 kN as shown in the figure :
[Figure, described in words: A is a fixed support on the left. AB is horizontal, 2 m long. From B the member turns vertically downwards for 0.6 m to C. From C a horizontal arm CD, 0.3 m long, projects to the right. A vertical downward point load of 12 kN acts at D.]
2026 · Civil Engineering Optional Paper I · 10 marksMains
Determine the 'shape factor' for the diamond-shaped section shown in the figure :
[Figure, described in words: a rhombus (diamond) with total width b along its horizontal diagonal and total depth d along its vertical diagonal, symmetric about both diagonals; the horizontal diagonal divides the depth into two halves of d/2 each.]
2026 · Civil Engineering Optional Paper I · 10 marksMains
A pretensioned beam 250 mm wide and 300 mm deep is prestressed by 12 wires (each 6 mm diameter) initially stressed to 1200 MPa with their centroid located at 100 mm from the soffit. Estimate the final percentage loss of stress due to elastic shortening, shrinkage, relaxation of steel and creep effect. Assume that the modulus of elasticity of steel and concrete are 210 kN/mm² and 35 kN/mm² respectively, creep coefficient = 1·6, residual shrinkage strain = 3×10⁻⁴ and relaxation of steel stress = 90 MPa.
2026 · Civil Engineering Optional Paper I · 10 marksMains
A steel plate girder is subjected to a maximum factored shear force of 2800 kN. The cross-section of the girder is shown in the figure. Design a suitable fillet weld to connect flange plates to the web. Assume shop welding. E250 grade of steel having f_u = 410 MPa is used. Use limit state method of design. Take γ_mw = 1·25 :
[Figure, described in words: a welded I-section with top and bottom flange plates each 650 mm wide × 25 mm thick, and a web plate 1500 mm deep × 15 mm thick between the flanges; each flange is connected to the web by fillet welds on both sides of the web.]
2026 · Civil Engineering Optional Paper I · 15 marksMains
Using limit state method, design a reinforced concrete circular column (with lateral ties) of height 3·0 m. It is subjected to an unfactored axial load of 1150 kN (dead load + live load). Use M25 grade of concrete and Fe500 grade of steel. Take effective length factor as 1·2. Show the design details in a neat sketch.
2026 · Civil Engineering Optional Paper I · 15 marksMains
A straight bar of alloy is mounted in a strut-testing machine with both ends pin jointed and loaded axially till it buckles. Using Euler's formula, calculate the maximum central deflection before the alloy material attains the yield point at 300 MN/m². Take bar length = 2·0 m, cross-section of the bar as 20 mm × 15 mm and modulus of elasticity E as 90 GN/m².
2026 · Civil Engineering Optional Paper I · 20 marksMains
Using moment distribution method, analyse the structure ABCD shown in the figure (joint B is rigid). The loading on the structure, moment of inertia of the members and other dimensions are clearly mentioned in the figure. Give neat sketch of bending moment and shear force diagram, indicating their values in the diagram :
[Figure, described in words: a horizontal beam ABC with A and C fixed to walls; AB is 7 m long with moment of inertia 2I and carries a 100 kN downward point load 4 m from A (3 m from B); BC is 5 m long with moment of inertia I and carries an 80 kN downward point load 2 m from B (3 m from C). A vertical column BD, 5 m long with moment of inertia 2I, hangs from joint B down to a fixed support at D.]
2026 · Civil Engineering Optional Paper I · 10 marksMains
A vertical member in a truss is subjected to the following member force (factored) :
(i) Compressive force = 30 kN (dead and live load)
(ii) Tensile force = 150 kN (dead and wind load)
The member is composed of two numbers ISA 100 × 100 × 8 connected to both sides of the gusset plate of thickness 10 mm. Find the number of bolts required at the joint. Assume bolt diameter = 16 mm, grade of bolt = 4·6, γ_mb = 1·25, k_b = 0·6, cross-sectional area at the threaded part of the bolt = 0·78 times that of shank. Use limit state method of design.
2026 · Civil Engineering Optional Paper I · 20 marksMains
The given figure shows the shear force diagram for a beam ABCDEF. The beam has hinge support at A and at one more point. Draw the load diagram and bending moment diagram (BMD) for this beam, indicating the shape of BMD between two successive points. Also show the point of contraflexure (if any) :
[Figure, described in words: points A, B, C, D, E, F along the beam with AC = 4 m, CD = 3 m, DE = 2 m and EF = 2 m (B lies between A and C, where the diagram crosses the base line). The shear force ordinate is 10 kN below the base line at A and rises in a straight line through zero at B to 2 kN above the base line at C; it stays at 2 kN above the line from C to D; at D it jumps up to 7 kN above the line and stays at 7 kN from D to E; at E it drops to 2 kN below the line and stays at 2 kN below the line from E to F.]
2026 · Civil Engineering Optional Paper I · 10 marksMains
Three bodies of weights 200 N, 800 N and 400 N are connected with inextensible strings, passing over the frictionless pulleys as shown in the figure. Using virtual work method, determine the force F required to make the motion impending to the left. Take coefficient of friction for all the contacting surfaces as 0·30 except for the pulleys which are frictionless :
[Figure, described in words: the 200 N block rests on a horizontal upper surface and the force F pulls it horizontally to the left. A horizontal string from its right side passes over Pulley 1 at the top edge of a slope inclined at 45° to the horizontal, and runs down parallel to the slope to the 800 N block resting on the slope. A string from the lower side of the 800 N block runs down the slope to Pulley 2 at the foot of the slope and then horizontally to the right to the 400 N block resting on the lower horizontal surface.]
2026 · Civil Engineering Optional Paper I · 10 marksMains
A simply supported beam ISMB 400 @ 61·6 kg/m has an effective span of 5 m. Find the design bending strength of the beam and the intensity of u.d.l. that the beam can carry under service condition. Assume that the beam is laterally supported. The grade of the steel is E250. The class of section is plastic. For ISMB 400, I_zz = 20458 cm⁴, Z_ez = 1023 cm³, Z_pz = 1176 cm³. Assume γ_m0 = 1·1. Use limit state method of design.
2026 · Civil Engineering Optional Paper I · 10 marksMains
Develop the stiffness matrix for the beam element AB with respect to the coordinates ① and ② as shown in the figure. Take modulus of elasticity and moment of inertia of beam section as E and I respectively :
[Figure, described in words: a cantilever AB of length l = 2 m, fixed at A on the left and free at B on the right. Coordinate ① is a vertical (downward) translation at B and coordinate ② is a clockwise rotation at B.]
2026 · Civil Engineering Optional Paper I · 10 marksMains
The nominal flow rate of water over a weir is 2 m³/s. A 1 : 10 scale model of the weir is tested in a water channel. Answer the following :
(i) What is the expected flow rate for the model?
(ii) If a force of 12 N is measured on the model, what force would be expected on the prototype?
2026 · Civil Engineering Optional Paper I · 10 marksMains
A venturi flume, 3.0 m wide at the entrance and 1.5 m wide at the throat, has a horizontal datum. If the depth of water at the entrance and at the throat is 0.75 m and 0.65 m respectively, calculate the theoretical discharge through the venturi flume. If a 0.2 m high streamlined hump is provided at the base so that a standing wave is formed downstream of the throat, calculate the specific energy and upstream depth for the same discharge.
2026 · Civil Engineering Optional Paper I · 10 marksMains
The shrinkage limit test was conducted in a laboratory and the following results were obtained :
Initial mass of saturated clay = 45.0 g
Final mass of dry clay pat = 31.2 g
Initial volume of soil in saturated state = 24.8 cc
Final volume of dry clay pat = 16.1 cc
Determine the following properties of the soil, if the soil is at water content of 28.5% :
(i) Shrinkage limit
(ii) Shrinkage ratio
(iii) Specific gravity of soil solids
(iv) Maximum volumetric shrinkage
(v) Linear shrinkage
2026 · Civil Engineering Optional Paper I · 15 marksMains
Assuming the law for the velocity distribution in the boundary layer as v/V = 2(y/δ) − (y/δ)², derive an expression for the thickness of boundary layer. Hence calculate the thickness of boundary layer at a point 2.5 m from the leading edge of a plate, if the size of the plate is 3.0 m long and 1.25 m wide, and it is immersed in the water moving at a velocity of 0.3 m/s. Take viscosity of water equal to 0.001 N-s/m². [Notations used in the above expression have their usual meanings]
2026 · Civil Engineering Optional Paper I · 15 marksMains
Water flows in a triangular channel having side slope 1 Horizontal : 1 Vertical and longitudinal slope of 0.001. Estimate whether the channel is mild, steep or critical sloped when a discharge of 0.2 m³/s flows through it. Assume Manning's coefficient n = 0.015. Also, determine for what range of depths, the flow will be on type 1, 2 and 3 curve.
2026 · Civil Engineering Optional Paper I · 10 marksMains
A retaining wall 5 m high with a smooth vertical back is pushed against a soil mass. What is the total passive pressure, if the horizontal soil surface carries a uniform load of 60 kN/m²? Also, determine the location of resultant thrust, where it is acting. The properties of the soil are as follows :
Effective cohesion = 35 kPa
Effective angle of shearing resistance = 20°
Bulk density = 19.5 kN/m³
2026 · Civil Engineering Optional Paper I · 10 marksMains
Discuss the effect of earthquake forces on the stability of earth dams.
2026 · Civil Engineering Optional Paper I · 15 marksMains
The data with respect to a normally consolidated clay are as follows :
Thickness of the clay layer = 3.0 m
Initial void ratio = 0.75
Liquid limit = 50%
Effective overburden pressure on the clay layer = 130 kN/m²
Increment of effective pressure on the clay layer = 50 kN/m²
Secondary compression index, Cα = 0.02
Time for completion of primary settlement = 2.0 years
What will be the consolidation settlement of the clay layer, six years after the completion of primary consolidation settlement?
2026 · Civil Engineering Optional Paper I · 15 marksMains
The plan of a foundation is shown in the figure. The uniform load intensity on the soil is 100 kN/m². Determine the vertical stress increment at a depth 4 m below the point O, using Boussinesq's method :
[Figure, described in words: the plan is a rectangle ABCD, 8 m long (AB and DC) and 4 m wide (AD and BC), with a semicircle of radius 2 m attached outward on side BC. O is the mid-point of BC and the centre of the semicircle, 2 m from B and 2 m from C.]
2026 · Civil Engineering Optional Paper I · 20 marksMains
Oil of specific gravity of 0.8 and kinematic viscosity of 1.5×10⁻⁴ m²/s is pumped at a rate of 0.015 m³/s through a 150 mm diameter, 325 m long pipe. Determine the Reynolds' number, pressure drop, average shear stress at the pipe wall and power required to maintain flow under the following conditions :
(i) If the pipe is horizontal
(ii) If the pipe is inclined at 10° with the horizontal and the flow is in the upward direction
2026 · Civil Engineering Optional Paper I · 15 marksMains
Consolidated drained tests on clay specimens were performed and the following results were obtained :
Specimen No. | Confining pressure (kPa) | Axial load (N) | Axial deformation (mm) | Volume change (cc)
1 | 200 | 410 | 11.0 | 7.0
2 | 400 | 850 | 12.3 | 8.5
3 | 600 | 1275 | 14.6 | 10.0
The initial diameter and length of saturated clay sample were 38 mm and 76 mm respectively. Determine the shear parameters in terms of total stress and effective stress. Also, comment on the results obtained and its application.
2026 · Civil Engineering Optional Paper I · 15 marksMains
What is vibroflotation technique? The results of sieve analysis for the backfill material used in a vibroflotation project are as follows :
IS sieve | Mass of the soil retained (g)
4.75 mm | 9.40
2.36 mm | 54.00
1.18 mm | 78.20
600 μm | 83.10
300 μm | 86.20
150 μm | 75.30
75 μm | 13.80
Determine the suitability number. What would be its rating as a backfill?
2026 · Civil Engineering Optional Paper I · 15 marksMains
A Francis turbine has a speed of 300 r.p.m. The inlet diameter of the turbine is 1.20 m and its width is 280 mm at the inlet. The vane thickness coefficient can be taken as 0.95. If at the inlet, the guide vane angle is 30° and the blade angle is 90°, determine the power produced by assuming an overall efficiency of 90%. Assume radial discharge at the outlet and take density of water as 1000 kg/m³.
2026 · Civil Engineering Optional Paper I · 5 marksMains
What is the significance of curves of constant stream function (CSF)? Explain why the stream function is useful in fluid mechanics.